资源列表
ADC-SERIAL-ok
- PIC16F877实现AD转换，并通过串口发送转换后的电压-PIC16F877 achieve the AD conversion, and sent through the serial port of the voltage conversion
485-2-shou-fa-ok
- PIC16F877c语言实现485收发一个字节的数据，接通电路可直接使用-PIC16F877 to achieve a 485 bytes of data can be directly connected to the use of circuit
485-PC-BUS-ok
- 吐血奉献，PIC16F877c语言实现485带起始结束符号的5位字串接收，并发送到串口显示-Blood sacrifice, PIC16F877c language starting with the end of 485 symbols to receive 5 string, sent to the serial display
delay-2-ok
- c语言一个子函数实现从1毫秒到1分钟的延时程序-c language of a Function from 1 ms to 1 minute delay procedures
DS18B20_www.ic37.com
- 资料，经典的重要的18b02资料，绝对有用，好资料啊，真的看过就知道，不看会后悔，真的好资料-Information on important classical 18b02 information is absolutely useful, good information, ah, really read, we know that do not will regret it, really good information
4X4key
- 单片机编程，4X4键盘，可以直接使用，非常好用-Single-chip programming, 4X4 keypad, you can directly use, very easy to use
4x4keyboardscan
- C语言编程，4X4键盘扫描程序，可以直接使用到51单片机中-C language programming, 4X4 keyboard scanner can be used directly in the 51 SCM
Commonsourcecode
- 常用源代码,包括LED,LCD,BEEP.-Common source code, including LED, LCD, BEEP.
FLASHLIGHTS
- 在P1.0端口上接一个发光二极管L1，使L1在不停地一亮一灭，一亮一灭的时间间隔为0.2秒。-P1.0 port access in a light-emitting diodes L1, so that L1 in a non-stop out of a bright, a bright a time out interval is 0.2 seconds.
ANOLOGSWITCH
- 监视开关K1（接在P3.0端口上），用发光二极管L1（接在单片机P1.0端口上）显示开关状态，如果开关合上，L1亮，开关打开，L1熄灭。 -Monitor switch K1 (then in the port P3.0), using light-emitting diodes L1 (in the single-chip access port P1.0) Show switch status, if the switch closed, L1 light, switch open, L1
Multi-waySwitchStatusIndication
- AT89S51单片机的P1.0－P1.3接四个发光二极管L1－L4，P1.4－P1.7接了四个开关K1－K4，编程将开关的状态反映到发光二极管上。（开关闭合，对应的灯亮，开关断开，对应的灯灭）。-AT89S51 MCU P1.0-P1.3 next four light-emitting diodes L1-L4, P1.4-P1.7 next four switches K1-K4, programming will reflect the status of switches on the
ShiftedtoRightofTheLeftAdvertisingLights
- 做单一灯的左移右移，硬件电路如图4.4.1所示，八个发光二极管L1－L8分别接在单片机的P1.0－P1.7接口上，输出“0”时，发光二极管亮，开始时P1.0→P1.1→P1.2→P1.3→┅→P1.7→P1.6→┅→P1.0亮，重复循环。-Left to do a single light shifted to right, the hardware circuit as shown in Figure 4.4.1, eight light-emitting diodes L1-L8, resp