资源列表
OTP-WHRITE-CTRL-REV-B-20121020
- LCD 工厂 OTP烧录时电压发生，转换控制程序，电压按照烧录过程启动，停止，升压，降压等-LCD factory OTP Programmer voltage occurs, change control procedures, voltage to start the burning process, stop, step-up, step-down
SYN6288
- SYN6288语音合成芯片的测试程序（51）单片机-Of SYN6288 speech synthesis chip test procedures (51) microcontrollers
UsbKeyboard
- USB键盘终于搞了一回USB HID设备,做了一个USB键盘来玩玩~~~~ 其中的报告描述符让我晕了几天~~~~~几份HID相关的协议还是蛮长的~~~~~~ 明天再弄个USB鼠标设备玩玩~~~~~~~有空的话再搞个红外遥控器-USB keyboard finally engage in a back USB HID device, a USB keyboard to play ~ ~ ~ ~ the report descr iptor makes me dizzy days ~ ~ ~
24c02
- C8051F单片机EEPROM通讯程序，I2C接口通讯-EEPROM communication for C8051F MCU，by I2C interface
test-12864-P-key
- 低功耗msp430控制，4*4矩阵按键，采用12864显示-Low-power msp430 control, 4 x 4 matrix keys, 12864 Display
HF3223程序
- 一款电力行业使用的温湿度控制器源代码 湿度传感器采用HF3223 温度采用DS18B20 单片机采用mega8 编程采用winavr2007
4
- 用PIC16F877A单片机的一组8个I/O端口连接LED发光二极管，让它们以跑马灯方式轮流闪烁发光。具体要求是：每个时刻只有一个LED被点亮，亮灯的位置以循环方式不停地移动，顺序为LED0→LED1→LED2→……LED7→全灭→LED0→LED1→……,每个LED被点亮的时间约为0.7s内，它将以8Hz左右的频率闪烁，即所谓“闪烁式跑马灯”。-PIC16F877A MCU, a group of eight I/O ports to connect the LED light-emittin
GuangminRemin
- 基于51单片机的光敏热敏电阻实验仿真源程序，C编程，内附电路图及详细注释-Based on the the 51 microcontroller photosensitive thermistor experimental simulation source, C programming, is equipped with a circuit diagram and detailed notes
MSP430
- 基于MSP430的气体传感器批量测试系统-MSP430-based gas sensor bulk test system
password-program
- 本密码程序设计是基于MSP430F149；密码长度1-16位可设置；可防止多次试探而不被破译（键盘锁住，输入无效约2分钟）。-The password program design is based on MSP430F149 password length can be set 1-16 without being deciphered (keyboard lock prevents multiple exploratory Invalid input for about 2 minut
MSP430-MCU-control-the-LCD12864
- 一个关于MSP430单片机控制12864液晶显示屏的程序，是个模板，以后开始时使用会比较方便。-12864 LCD program an MSP430 MCU control, is a template, after the start would be more convenient to use.
temperature-alarm
- 这是一个简单的温度高低报警器，可以设置温度上限和温度下限，一旦温度满足设定条件，蜂鸣器就会发出声音进行报警。内带PROTUES仿真，可直接查看效果。-This is a simple and low temperature alarm, you can set the temperature of the upper and lower temperature limit, the buzzer will sound the alarm once the temperature to meet