资源列表
adc10
- 单片机msp430x22x4的ADC转换读取温度-SCM msp430x22x4 read the temperature of the ADC conversion
ARM-Cortex-M3
- ARM-Cortex-M3内核，很有用的文件-ARM-Cortex-M3
led
- 该程序通过单片机AT89C51来控制LCD(LGM1264)来实现汉字(诗句)的功能.-The program through the AT89C51 microcontroller to control the LCD (LGM1264) to achieve the Chinese character (verse) function.
a
- 该程序通过单片机8051及相关电路控制实现播放音乐的功能.-The program through the 8051 microcontroller and associated circuitry to achieve control of music functions.
test
- 将拨码开关全部拨到on，将会看到数码管从 0-9 A-F逐个显示；按下8个按键中的任何一个，对应的LED灯会亮，按第一个按键时，蜂鸣器会响。-All appropriated for the DIP switch on, will see the digital tube display one by one from the 0-9 AF press 8 keys in any one, the corresponding LED lantern light, according to th
9421
- 9421是一种新型数控电位器，内含四个独立电位器，功能极其强大。通过IIC总线与单片机通讯。包敬海原创。-9421 is a new, digitally controlled potentiometers, containing four separate potentiometer, extremely powerful. Through the IIC bus and Single-Chip Communication. Jing Hai original package.
pwmtest
- 拨码开关控制PWM的占空比为16级，分别对应电压3.3伏16分之一的倍数-DIP switch control PWM duty cycle is 16, corresponding to voltage of 3.3 volts, one of the 16 sub-multiples
uart
- 实现bq26500对于锂电池电压等数据的动态监测-Achieve the bq26500 Li-ion battery voltage and other data for the dynamic monitoring of
sensortest
- 光线传感器测量 LED会显示环境光的大小，用手挡住光线 传感器，LED的显示值会相应减小。-Light sensors measure the ambient light LED will show the size, hands blocking the light sensor, LED display the value of a corresponding decrease.
LM386
- 设计并制作一个电能收集充电器，充电器及测试原理示意图如图1。该充电器的核心为直流电源变换器，它从一直流电源中吸收电能，以尽可能大的电流充入一个可充电池。-Design and production of electrical energy to collect a charger, charger and test schematic diagram of Figure 1. The core of the charger DC power converters, which flows fro
test
- 将拨码开关全部拨到on，将会看到数码管从0-9 A-F逐个显示；按下8个按键中的任何一个，对应的LED灯会亮,按第一个按键时，蜂鸣器会响。-All appropriated for the DIP switch on, will see the digital tube display one by one from the 0-9 AF press 8 keys in any one, the corresponding LED lantern light, according to the
PWMtest
- PWM 转模拟信号 拨码开关控制 PWM 的占空比为16级，分别对应电压3.3伏16分之一的倍数-DIP switch to an analog signal PWM switch control PWM duty cycle is 16, corresponding to voltage of 3.3 volts, one of the 16 sub-multiples