资源列表
ucos-ppc
- ucos-ppc，将ucos 2.52移植到ppc处理器mpc8247/8270/8260上。这里ucos运行时已经用uboot加载，所以省略了一些系统初始化的过程，但任务切换、中断响应、bsp还是有一定参考价值，且附带了bsp的应用编程接口。-ucos-ppc, implement ucos 2.52 in ppc processer mpc8247/mpc8270/mpc8260。Here ucos is bootloaded by uboot, so it omits several in
rtems_build_system_analysis
- rtems配置编译系统分析： rtems安装使用configure进行配置，然后使用make编译，最后用make install进行安装。本文就是介绍在这其中rtems都做了什么。本文主要分析configure生成需要的脚本、makefile生成需要的脚本、rtems代码编译过程、rtems系统安装过程。-rtems configure and build system analysis: rtems uses gnu install process: configure-> ma
rtems_sparc-leon2
- rtems实时操作系统sparc leon2处理器的bsp代码分析文档。包括rtems在sparc leon2处理器上系统启动、任务切换、中断响应、硬件驱动（定时器、串口等）等代码模块的分析。-The document of rtems(RTOS) bsp code on sparc leon2 processor, including system startup、task switching、interrupt handling、device drivers(timer、serial por
1802
- msp430g2553简单温控系统 制定上限下限报警-msp430g2553 simple temperature control system to develop the upper limit and lower limit alarm
u-boot-1.1.1-ppc
- uboot-ppc源代码： 将uboot 移植到ppc处理器mpc8247/mpc8260/mpc8270上，命令丰富、设备驱动详尽（包括SDRAM、NOR Flash, NAND flash, serial, timer, watchdog等等),对学习理解ppc处理器和板卡很有帮助。 -uboot-ppc src: implemente uboot in ppc processor mpc8247/mpc8270/mpc8260。It has a lot of commands, a
STC89C52andX5045
- STC89C52源代码，功能主要包括：看门狗、键盘、数码显示，通信控制。-STC89C52 source code, functions include: watchdog, keyboard, digital display, communication control.
STC89C52and7279
- STC89C52与7279程序控制与键盘等功能同时使用。-STC89C52 7279 program control and keyboard functions are used simultaneously.
DEMO(1.2-22.1184)
- 通过单片机STC89C52的中断控制，通过检测外部信号控制输出信号。-SCM STC89C52 interrupt control, control output signal by detecting external signals.
CH451
- 基于STC12C5A60S2单片机的CH451键盘和数码管驱动，IO口扩展-CH451 keyboard based on STC12C5A60S2 microcontroller and digital tube driver IO port expansion
DDS
- 基于STC12C5A60S2单片机的DDS模块驱动程序-The DDS module based on STC12C5A60S2 MCU driver
NOKIA3510I_C51
- 基于STC12C5A60S2单片机的nokia5310液晶模块驱动程序-Based on STC12C5A60S2 microcontroller nokia5310 LCD module driver
reset
- 基于STC12C5A60S2单片机的的软件复位实例程序-STC12C5A60S2 microcontroller-based software reset the instance of the program