资源列表
danpianji2
- 掌握如何使用803l的外部中断方法。掌握中断的程序设计方法。中断响应时，P1．4～P1．7显示P1.0~P1.3的开关状态，要求外部中断采用边沿触发式。 实验原理图与建议接线图如下图所示： -To grasp the method of how to use the 803 l external interrupt.Mastering the interrupt program design method.Interrupt response, P1.4 ~ P1.7 shows P1
dht22
- stm32 dht22 dht11 stm32 dht22 dht11 - stm32 dht22 dht11 stm32 dht22 dht11
timer
- 定时器功能实现，TMS320C6748+CCS-TMS320C6748+CCS TIMER
led
- 基于DE2—115的跑马灯试验例程 8个灯来回闪烁-8 LED lights flashing cycle
51
- 51单片机源程序 DS1302S时钟显示 RF905无线模块代码 -51 microcontroller source DS1302S clock display RF905 wireless module code
menling
- 当按下QX-MCS51上的S2键后，蜂鸣器会发出十次短暂的“嘟嘟”声作为呼叫。 S3用于关闭或者打开门铃。 当门铃处于关闭时，按下S2不会有呼叫效果。-When you press the S2 key on the QX-MCS51, beeper ten times short " beep" as a call. S3 is used to close or open the door. When the door is closed, press S2
loutizaoming
- 实现楼道间照明灯的方便控制，一个照明灯，在楼上和楼下各有一个（闭合式）开关控制。-Achieve inter-corridor lighting control convenience, a lamp, upstairs and downstairs each have a (closed) switch.
canpinshuliangjishuqi
- 其中S2用于模拟代替扫描开关，当有产品经过时，会使S2送出低电平（本程序中是用手按下S2来模拟） S2每按一下，便会使数码管上的计数器加一。-Wherein S2 is used in place of the analog scanner, when the product passes, S2 will send a low level (this program is to simulate hand pressing S2) S2 each click, it will make
24l01ceshi
- 液晶1脚接1602黑色排母的1脚 如果是无背光的液晶只有14个脚 排母右边空2个位 请把液晶对比度电位器顺时针调制10点钟方向，请勿多调超出极限位置会损坏电位器！-1602 black crystal pin 1 to 1 foot row home if it is not backlit LCD only 14 feet right of the row home empty two bits Please LCD contrast potentiometer clockwise m
hongwai
- 名称：遥控器红外解码数码管显示 内容：按配套遥控器上1-9会在数码管上对应显示-Name: Infrared remote control decoding digital display: Press 1-9 on the remote control will be supporting on the corresponding digital display
mdk
- 飞思卡尔k60基于MDK的样例程序，开发模板-NXP K60 MDK based on the sample program, the development of template
K60-ADC
- k60基于mdk 的模数转换实验，样板工程-MDK based on K60 analog to digital conversion experiment