资源列表
1302
- 1302的使用，包含测试1302激活的函数，包含基本的使用-use 1302
LED_controlled_by_keys
- 程序实现如下模拟彩灯，开发板从左至右4个按键分别为S1-S4，从上至下8个灯为L1-L8，按下S1键8只LED小灯以1HZ频率闪烁，按下S2键8只灯奇偶交替点亮，间隔0.3S，按下S3键，L1-L4与L5-L8灯交替点亮，间隔0.2s，按下S4键熄灭所有灯。-Lantern simulation program to achieve the following development board left to right are four buttons S1-S4, top to bot
pinlvji
- 频率计在上电后，具有：能测试1-100HZ的低频信号；并把结果显示在数码管上。误差小于1HZ。-After power-frequency meter, comprising: a low-frequency signal to test the 1-100HZ and the results are displayed on digital tube. Error is less than 1HZ.
xinhaofashengqi
- 按下S1从单片机第1个引脚上输出频率为1KHz的方波，再按下S1则停止输出方波； 方波频率误差小于1 。 晶振频率：11.0592MHz-Press S1 output the first one on the microcontroller pins 1KHz square wave frequency, and then press the square wave output S1 is stopped Square-wave frequency error is less
stopwatch
- 数码秒表设计:开发板上4键从左至右为S1-S4，上电后，开始时显示 0.0 ； 利用S1按键后启动计时；S2按键后停止计时；S3按键后计时归零；最大计时 为9.9秒。计时误差小于0.2秒，显示稳定。 晶振频率：11.0592MHz -Digital stopwatch design: 4 key development board left to right S1-S4, after power is displayed at the beginning of 0.0 S
daojishi_miaobiao
- 倒计时秒表设计:使秒表在上电/复位后，具有：开始时显示 9.9 ；并开始倒计时， 当9.9S计时到，数码管显示0.0并闪烁，同时蜂鸣器发声报警3S，倒计时误差小于0.2秒。 晶振频率：11.0592MHz-Countdown stopwatch design: stopwatch after power-on/reset, comprising: a display at the beginning of 9.9 and begins the countdown, When t
SoftwareSerial
- arduino program for serial communication
guanggaoxianshiping
- 基于89C51单片机的实例程序，实现广告显示屏的一些功能-Based on 89C51 instance procedures, some of the features of the display ad
uCOSII_v2.91
- 代码是在STM32上移植的ucosII，ucos版本号为2.91。移植后有简单LED显示，可作为ucos研究的模板使用。-Code is on the STM32 transplant ucos II, ucos version number is 2.91. After transplantation simple LED display can be used as a template to use ucos research.
Maxplus2_74LS161
- 用Maxplus2制作的实现74LS161数字芯片功能，入门级工程。-Maxplus2 made with digital chips to achieve 74LS161 function, entry-level engineering.
chuankoutongxin
- msp430f149计算机串口通信，串口通信程序-MSP430F149 serial communication
2660
- 淘宝买的，很好用的RTD2660程序淘宝买的，很好用的RTD2660程序-Taobao to buy, easy to use RTD2660 programTaobao to buy, easy to use RTD2660 program