资源列表
tiaoguang-20120926
- 基于瑞萨78K0S/Kx1+ uPD78F9202开发的调光开关源代码-light change
Source-Code(2014.11.12)
- 基于CAN2.0B协议的智能SSPC程序，带过流保护过压保护，电流电压查询功能，在MPLAB环境下开发，已调试通过-Based on intelligent SSPC CAN2.0 protocol B procedures, with over-current protection over voltage protection, current voltage query function, in the MPLAB environment development, have been de
Ultrasonic-level-measurement
- 超声波测液位，采用超声波作为主要的手段，用AT89C51单片机，进行程序的设计。-Ultrasonic level measurement
ucos-freescale-9s12
- 经过产品验证的freescale mc9s12g128上移植的ucos-ucos freescale mc9s12g128
Audiovisual-protection
- 本文提出了一种基于单片机的多功能视力保护器。讨论了8051型单片机的硬件电路和软件设计。并在此硬件基础上实现传感器报警电路、光线强度报警电路及定时报警电路-Audiovisual protection
24.KH25L8005_SPIreadwrite
- C8051F 单片机读取EEPROM程序，通过SPI总线读取，单片机配置成4线单主机模式，且EEPROM是SPI总线上的唯一从机设备-This program accesses a SPI EEPROM using polled mode access. The F04x MCU is configured in 4-wire Single Master Mode, and the EEPROM is the only // slave device connected to the
Solar-solar-tracking-controller
- 根据太阳位置的变化，时刻调整太阳接收板的位置，是接受的太阳能利用率最大 -Solar solar tracking controller
25.KH25L8005_SPIREADandWrite2
- C8051F04X单片机被配制成4线单主机模式，SPI时钟500KHZ，因为SPI从机翻译主机指令和写相应数据到SPIODATE寄存器需要一定的时间-This program configures a C8051F04x as a 4-wire SPI Single Master. // // The SPI clock in this example is limited to 500 kHz when used with the // SPI0_Slave code exampl
5fLOOR-ELEVATOR_PLC
- 5层电梯的PLC程序，使用GXdeveloper 软件开发，PLC型号为三菱FX2N-64MR。-Five layers of elevator PLC program, using GXdeveloper software development, models for mitsubishi FX2N- 64- Mr PLC.
ADC-Cfor-STC15W204
- STC15W204S单片机AD采样程序，程序中附原理图，是模拟ADC，采用的是内部比较器实现的，STC15W204S单片机本身不带AD-STC15W204S MCU AD sampling program, the figure, the principle is to simulate the ADC, USES is the internal comparator, STC15W204S microcontroller itself without AD
ADS1256-STM32
- 这是一个STM32+ADS1256A/D转换器的驱动测试程序，非常方便使用的一个东西 。-This is a STM32+ ADS1256A/D converter driver testing procedures, a very convenient thing to use.
10_rom_test
- rom test,基于FPGA的rom测试，很好的学习资料，大家都来学一学-rom test