资源列表
fixed-text
- uc/gui低版本的text控件不能settext，这两个文件添加后即可settext-uc / gui version of the text low Control settext not, the two documents can be added after settext
8279program
- 8279键盘显示程序，对作毕业设计有用。-8279 keyboard display program to design useful for graduation.
gdb-5.0-uclinux-armulator-20060104.patch
- uClinux移植的具体步骤，以及应用仿真环境下GDB工具的具体实现情况，及相关的命令及其他一些简单的代码。-uClinux transplant concrete steps Simulation environment and the application of tools GDB under a concrete realization of the situation and related orders and other simple code.
nbd8279program
- 8279键盘显示程序，对作毕业设计有用。-8279 keyboard display program to design useful for graduation.
xms
- DOS XMS library is a DOS real mode and large memory model C library. Because DOS is ran under real mode, programmer only can access RAM under 1MB-DOS XMS library is a real mode DOS and large m emory model C library. Because ran under DOS is r Leverag
shengrege
- 程序运行后在接在单片机的P3.3上的小喇叭唱生日快乐歌 -after running in the next P3.3 MCU on the loudspeaker to sing a happy birthday song
wenduchuanganqi
- 温度传感器ds1820 的汇编程序 晶振：12M -temperature sensor ds1820 compilation procedures crystal : 12M
paomading
- 单片机应用 p1口八个灯作跑马灯。 8个灯依次点亮-SCM application p1 mouth eight lights for 5,250. Eight lamps were lit
data_vol_counter
- 数字电压表 利用单片机AT89S51与ADC0809设计一个数字电压表，能够测量0－5V之间的直流电压值，四位数码显示，但要求使用的元器件数目最少。 -digital voltmeter SCM AT89S51 ADC0809 design with a digital voltmeter, capable of measuring 0 - 5V DC voltage between the value of four digital display, but requires
jycc
- dsp5509得基因检测程序 基因检测-dsp5509 in genetic testing procedures gene detection
sibieqi
- 一键多功能按键识别技术 如图4.9.1所示，开关SP1接在P3.7/RD管脚上，在AT89S51单片机的P1端口接有四个发光二极管，上电的时候，L1接在P1.0管脚上的发光二极管在闪烁，当每一次按下开关SP1的时候，L2接在P1.1管脚上的发光二极管在闪烁，再按下开关SP1的时候，L3接在P1.2管脚上的发光二极管在闪烁，再按下开关SP1的时候，L4接在P1.3管脚上的发光二极管在闪烁，再按下开关SP1的时候，又轮到L1在闪烁了，如此轮流下去。-a multifunctional ke
zhuangtaizhishi
- 多路开关状态指示 如图4.3.1所示，AT89S51单片机的P1.0－P1.3接四个发光二极管L1－L4，P1.4－P1.7接了四个开关K1－K4，编程将开关的状态反映到发光二极管上。（开关闭合，对应的灯亮，开关断开，对应的灯灭）。 -multiple switch state instructions shown in Figure 4.3.1. AT89S51 SCM P1.0 - P1.3 then four LED L1 - L4, P1.4 - P1.7 then sw