资源列表
Anglesensor
- 使用单轴倾角传感器SCA61T测量角度，并在12864液晶上实时显示。本代码包括液晶初始化和倾角传感器初始化，使用的430F169单片机的SCL总线-The use of single-axis inclination angle sensor SCA61T measurement and real-time display on the LCD 12864. The LCD initialization code, including initialization and angle sens
MSP430_01
- MSP430系列超低功耗16位单片机原理与应用-MSP430 family of ultra low-power 16-bit single-chip Principle and Application
MSP430_001
- MSP430 单片机通用系统研制和应用.pdf 介绍了MSP430 单片机 13x 14x系列的功能特点 并以其为核心研制的通用系统和应用举例-MSP430 single chip development and application of general systems. Pdf introduced 13x 14x series of single-chip MSP430 features and its development as the core of the common sy
sci
- SCI调试主程序 DSP与PC机通过SCI连接 测试sci接口是否工作-SCI debug the main program through the DSP and PC-connectivity test sci interface SCI is working
0832C
- ADC0832 非常好的程序 ADC0832 非常好的程序 ADC0832 非常好的程序 ADC0832 非常好的程序 ADC0832 非常好的程序-ADC0832 very good very good procedures ADC0832 procedures ADC0832 procedures ADC0832 very good very good very good procedures ADC0832 procedures ADC0832 procedures ADC0832 ver
88M
- 本代码使用Keil uVision3编程使用c语言编写作用是给单片机c8051f120，8倍频。-Keil uVision3 use this code to use c programming language to the single-chip microcomputer is c8051f120, 8 octave.
uart0
- 本代码是在Keil uVision3环境下使用c语言编程作用是使用串口调试助手与单片机通信，使用max232进行电平转换后进行通信。-The code is in the Keil uVision3 environment the role of c language programming is the use of single-chip serial debugging assistant and communications, the use of level translators m
AD_1V
- 本代码是在Keil uVision3环境下使用c语言编写的。功能是使用片内模数转换转换1V电压。-The code is in the Keil uVision3 environment c languages. Feature is the use of analog-to-digital conversion chip voltage conversion 1V.
AD_sinx
- 本代码是在Keil uVision3环境下使用c语言编写的。功能是使用片内模数转换器转换一个正选拨变换的电压。-The code is in the Keil uVision3 environment c languages. Function is to convert the use of one-chip ADC is the voltage transformation selection.
c51-source-book
- keilc51中所有的源程序，c51-source-book-keilc51 all the source code, c51-source-book
24c02
- 24C02的程序 非常好2 4C02的程序 非常好2 4C02的程序 非常好-24C02 procedure 24C02 procedure very good very good very good procedures for the 24C02 procedure 24C02 very good very good procedures 24C02
DA-
- 本代码是在Keil uVision3环境下使用c语言编写的。功能是使用片内数模设备将数字信号转换为模拟信号。-The code is in the Keil uVision3 environment c languages. Feature is the use of digital-analog-chip digital signal equipment will be converted to analog signals.