资源列表
CapactiveTouchSense
- Capacitive touch sensing technology implementation with source code.
ARM1
- ARM 嵌入式系统实验教程 ARM 嵌入式系统实验教程-ARM 嵌入式系统实验教程ARM 嵌入式系统实验教程ARM 嵌入式系统实验教程ARM 嵌入式系统实验教程
Chinese_display_for_protel99se_pcb_or_dxp2004
- 这是一个PCB汉字封装库,使用前先写好自己的名字,然后把该库加进去,在PCB里即可放置.是弥补了protel 99和dxp 2004不能放汉字的缺点.-this is a PCB footprint library for protel 99 or dxp 2004.
nios_lcd_3c120
- Cyclone III FPGA Nios II LCD开发程序，包括QuartusII工程及Verilog源码。-Cyclone III FPGA Nios II LCD development process, including the QuartusII engineering and source code.
weatherglass
- 用一片DS18B20构成测温系统，测量的温度精度达到0.1度，测量的温度的范围在－20度到＋100度之间，用8位数码管显示出来。-This design introduces a controlling circuit which is realized by scp AT89C51 in details.Use DS18B20 consitu temperature sysmtem. Display with LED.
AD
- 从ADC0809的通道IN3输入0－5V之间的模拟量，通过ADC0809转换成数字量在数码管上以十进制形成显示出来。ADC0809的VREF接＋5V电压-This design introduces a controlling circuit which is realized by scp AT89C51 in details. ADC0809 converted into digital by the digital pipe to form a decimal display
pinlv
- 利用AT89S51单片机的T0、T1的定时计数器功能，来完成对输入的信号进行频率计数，计数的频率结果通过8位动态数码管显示出来。要求能够对0－250KHZ的信号频率进行准确计数，计数误差不超过±1HZ。-AT89S51 microcontroller using T0, T1 timing counter functionality to complete the input signal frequency count, counting the frequency of the result
titi
- 用AT89S51单片机产生“嘀、嘀、…”报警声从P1.0端口输出，产生频率为1KHz，根据上面图可知：1KHZ方波从P1.0输出0.2秒，接着0.2秒从P1.0输出电平信号，如此循环下去，就形成我们所需的报警声了。-Use AT89S51 microcontroller have a "tick, tick, ..." alarm sound from the P1.0 port output, resulting in a frequency of 1KHz, according to the
keil
- 本文介绍80c51编程技巧，硬件和软件的介绍 。-This article describes the 80c51 programming skills, hardware and software presentations.
ucoscode
- ucosII源码 61ic 网 原创启动编译源码-ucosII original source 61ic net compiling source code
hp3070prog
- 编程XC9500 惠普CPLD 3070 测试仪 经典教程-Programming Xilinx XC9500 CPLDs on HP 3070 Testers
the_method_of_embed_soft
- 讲解嵌入式编程的一些注意事项，一个多年工作经验的工程师的心得-my english is not so so