资源列表
STC-9132-54106
- 程序主要实现了两种功能，一个是模拟串口程序，因为STC单片机不自带串口，另一个功能就是IIc的驱动，各自一个H文件，很容易引用-Program achieved a major two functions, one is to simulate serial process, because STC microcontroller serial port does not own, and the other function is to IIc driver, each an H file,
tetris
- 自己写的STC89C52RC单片机俄罗斯方块完整代码，清晰易懂-51 single Tetris complete code
51_USART
- 适用于51单片机的串口程序，采用缓冲数组编写，最大限度避免冲突。-For 51 microcontroller serial procedures, using the write buffer array, the maximum to avoid conflicts.
1-LED
- LED流水灯，跑马灯，左右跑马灯以及接线图和排线连接说明-LED running lights, marquees, so marquee and wiring diagram and cable connections
9-LED-lattice
- LED流水灯，跑马灯，左右跑马灯以及接线图和排线连接说明-LED running lights, marquees, so marquee and wiring diagram and cable connections
K60-USB-CARDREADER
- 使用飞思卡尔ARM K60制作的USB读卡器，主要包含K60的USB2.0模块和spi模块。-Produced using Freescale ARM K60 USB card reader, USB2.0 module mainly contains the K60 and spi module.
Bluetooth_20130916
- MC9S12XEP100的SCI接收CAN发送程序,本用于蓝牙通信.程序经过调试,并用板子和蓝牙模块测试过.-The SCI receive CAN MC9S12XEP100 sending program, the communication for Bluetooth. Program after debugging, and use the board and Bluetooth module tested.
Knock-signal-check
- 使用飞思卡尔 DZ60 做的爆震信号检测工程，通过提取压电片信号并积分检测判断汽车爆震强度。-DZ60 done using Freescale knock signal detection works by extracting the piezoelectric film signals and integral test to determine car knock intensity.
engine-signal-Simulation
- 使用DZ60单片机制作的发动机信号模拟器，模拟发动机的曲轴凸轮轴等数字信号和水温等模拟信号，供控制器开发使用。-DZ60 MCU production of engines using signal simulator to simulate the engine crankshaft camshaft and other digital signals and analog signals such as water temperature, used for controller devel
measurement-of-injector
- 喷油嘴参数自动测量，通过油泵，电子天平和单片机快速的测量出汽车喷油在不同压力和电压下的流速，死区时间等参数。-Injector automatic measurement parameters, the oil pump, electronic scales and fast measurement of automotive microcontroller injection pressure and voltage at different flow rates, dead time and
c-pulse
- 利用脉冲计数测量汽车变速器输入、输出轴转速-Automobile transmission measurement using pulse counting input and output shaft speed
ADC0832P1602
- 51单片机ADC0832+LCD1602 proteus 仿真源程序，包括proteus原文件，可以直接仿真。在keil+proteus 7.8上测试通过。-51 MCU ADC0832+ LCD1602 proteus simulation program, including proteus original documents can be directly simulated. In keil+ proteus 7.8 on the test.