资源列表
i2c
- PIC16F877A对AT24C02读写代码，实现延时、初始化、写和读操作-PIC16F877A on AT24C02 write code to achieve delay, initialization, write and read operations
pic16f886
- pic16f886采用AD作为按键输入，可以很好的减少单片机的引脚使用，更大限度的利用io资源-pic16f886 using AD as a key input, can be very good to reduce the microcontroller pins, a greater level of resource utilization io
Tower-type
- 水塔模拟：低水位送水，达到低位仍然加水，达到高位停止。若高位为1，低位为0，报错。-Tower Simulation: low water and bottled water is still low, add water to achieve, achieve high stop. If the high is 1, the low is 0, error.
Ultrasonic-Ranging
- 超声波测距：根据距离显示不同数值，精确度0.3mm，可测2cm到4M-Ultrasonic Ranging: display different values depending on the distance, the accuracy of 0.3mm, can be measured 2cm to 4M
PWMtim2PFM
- 产生一个占空比为50 的脉冲PWM波形，要求这个脉冲波形按照以下要求对脉冲频率进行变化： 从500KHz（对应2us周期）到10KHz（对应100us周期)每个脉冲周期时间递增，每次递增1us。当脉冲周期时间递增到100us时，下一个脉冲周期为2us。如此循环-From 500 KHZ (corresponding to 2 us cycle) to 10 KHZ (100 us cycle) corresponding to each pulse cycle time increasing
LCD1602
- 本程序提供了在STC90单片机上的系统电压值、温度、光照强度等通过AD转换显示在LCD1602或LED数码管上。-This program provides the STC90 MCU system voltage, temperature, light intensity through AD conversion LCD1602 display or LED digital tube.
DIJI
- 本程序提供了在STC90单片机上的系统电压值、温度、光照强度等通过AD转换显示在LCD1602或LED数码管上。-This program provides the STC90 MCU system voltage, temperature, light intensity through AD conversion LCD1602 display or LED digital tube.
SIXIANDIJI
- 本程序提供了在STC90单片机上的系统电压值、温度、光照强度等通过AD转换显示在LCD1602或LED数码管上。-This program provides the STC90 MCU system voltage, temperature, light intensity through AD conversion LCD1602 display or LED digital tube.
stm32paomadeng
- 本程序提供了在STC90单片机上的系统电压值、温度、光照强度等通过AD转换显示在LCD1602或LED数码管上。-This program provides the STC90 MCU system voltage, temperature, light intensity through AD conversion LCD1602 display or LED digital tube.
15-STM32-ADDA-PCF8591
- 本程序提供了在STM32单片机上通过控制AD转换器PCF8591实现在LCD1602中显示传感器传输的值。-This program provides the STM32 microcontroller through the AD converter PCF8591 achieve control display value of the sensor in the transmission of the LCD1602.
21-DS18B20
- 本程序基于STM32单片机在LCD1602 或led数码管中显示18b20检测到的温度值。-The program is based STM32 MCU display 18b20 temperature values detected in LCD1602 or led digital tube.
proteus
- 单片机开发程序，基于PORTEUS的仿真程序，包括程序跳转，定时器，动态数码显示等-MCU development program, based PORTEUS simulation program, including jumps, timers, dynamic digital display