资源列表
tempAndLev
- 水位和水温度读取，判断是否超过水位或者是否超过温度。具有串口发送功能，将水位和检测信息发送到电脑端，完成水位检测。-The water level and water temperature reading, determine whether exceeds the level or over temperature. With the serial port to send function, the water level and the detection information is
STC89C52_PCF8591
- 使用keil4软件打开。源码中，通过单片机采集光敏电阻数据，以及超声波数据。得到当前环境的光照程度以及使用者离设备的距离，并且判断是否在有效的光线或者距离范围。给出声光指示，同时将数据发送到串口中。-Use the software to open keil4. The source, collection of photosensitive resistance data through the microcontroller, and ultrasonic data. Get the cur
FunctionPower_s12864_use12C5A60S2
- 使用STC12C60S2单片机作为主控制芯片，配合x9312数字电位器，实现大功率三角波和方波的电源输出。-The use of STC12C60S2 microcontroller as the main control chip, with X9312 Digital Potentiometer, realize the power supply output power triangle wave and Fang Bo.
HDMI_OLED-DEMO_forMaple_UserSSP_IIC
- 使用maple IDE打开。采用PIC单片机pic16F1825作为主控芯片，完成对HDMI接收机ADV7611以及微型OLED显示器SVGA050的配置，实现HDMI显示器控制。-Using PIC MCU pic16F1825 as the main control chip, the completion of the HDMI receiver ADV7611 and the configuration of micro OLED SVGA050 display, HDMI displa
ADC
- 此源码是基于stc89c91的程序，为ADC0804的单片机程序-This source code is based on the application of stc89c91, as ADC0804 MCU application
DAC
- 这是基于stc89c52的单片机程序，为DAC转换的程序源码-This is based on stc89c52 singlechip procedures, for the DAC conversion program source code
LED
- 这是基于stc89c52的单片机程序，为点亮一个led的程序源码-This is based on stc89c52 singlechip procedures, to light up an led source program
leds
- 这是基于stc89c52的单片机程序，为点亮流水灯的程序源码-This is based on stc89c52 singlechip procedures, for the light water lamps program source code
multkey
- 这是基于stc89c52的单片机程序，为矩阵键盘的程序源码-This is based on stc89c52 single-chip microcomputer program for matrix keyboard program source code
18B20
- 通过温度传感器DS1820采集温度，在数码管上显示出温度值，第一个数码管显示正负。当前测得温度为19.87。当手放到DS1820时，数码管显示温度为20.06。-By collecting temperature DS1820 temperature sensor, showing the temperature on the digital control, the first sign of a digital display. The current measured temperatur
ds1302timers
- 8位数码管显示位时钟状态， 格式为:00（小时）—00（分钟）—00（秒）。 当按下K1键时，数码管时钟停止。当按下K2时，进行时钟调时。当按下K3时，进行时钟调分。当按下K4时，时钟继续开始。-8-bit digital display clock status, format: 00 (h)-00 (min)-00 (seconds). When you press the key K1, digital clock is stopped. When pressed K2, conduc
keyboard520
- 按下S1数码管显示0，按下S2数码管显示01， 按下S3数码管显示012，按下S4数码管显示0123， 按下S5数码管显示01234，按下S6数码管显示012345， 按下S7数码管显示0123456，按下S8数码管显示01234567， 按下S9数码管显示12345678，按下S10数码管显示23456789， 按下S11数码管显示3456789A，按下S12数码管显示456789Ab， 按下S13数码管显示56789AbC，按下S14数码管