资源列表
DS1302-18B20-display-in-12864
- MSP430 编程 在12864上可显示温度、时间、AD模拟温度。具有按键调时功能，华丽的菜单显示具有三级菜单功能，可进入低功耗。-MSP430 programming in analog temperature of temperature, time, AD can be displayed on the 12864. Function when the key tone, gorgeous menu with three menu functions, you can enter a lo
modbus
- Modbus RTU通讯协议在STC12C5A系列单片机上的实现，包括串口通讯的实现，实现了1，2，3，4，5，6，15，16号功能码的具体过程，程序编写时，考虑了调试的可配置性和可移植性，可以方便地移植到其它单片机平台上。-The realization of MODBUS RTU protocal for MCU, function number of 1,2,3,4,5,6,15,16 are realized properly.
Keeloq
- 包含Keeloq滚动码的简易编码，标准编码以及复杂编码的解码程序！编译环境MapLab IDE-Contains Keeloq rolling code simple codes, standard codes, as well as the complexity of coding, decoding program!
BootLosder_Training
- 基于CAN总线的Bootloader培训资料！-Based on CAN Bus Bootloader training materials!
TaTb_Fre_Meter
- MSP430测频1HZ - 33MHz用两个定时器TATB一个计数一个计时-MSP430 measured frequency 1HZ- 33MHz timer using two TATB count a time
Bootloader-for-HCS12X
- Bootloader in C for Freescale HCS12X. Uses serial SCI (UART) to load S19 files. It does not make use of XGATE
E1
- IIC总线驱动程序，msp430控制EEPROM（AT24C02）读写，指定地址读写，连续地址读写-IIC bus driver, msp430 control EEPROM (AT24C02) read and write, read and write the specified address, consecutive address read and write
hc-sr04
- 89c52单片机。用HC-SR04超声波测距，然后用1602的液晶来显示。-89c52 microcontroller. HC-SR04 ultrasonic ranging, and then the 1602 LCD display.
danpianji-
- 采用51单片机，开发工具为KEIL.主要功能是实现一个多功能温度计。采用1602液晶显示和配合上位机软件共同完成环境温度的检测与报警功能。系统可以通过按键或者上位机修改报警温度上下限。并将数值保存在外置的EEPROM中，以便开机的时候自动加载。-This work is entirely in accordance with the commercial and practical design requirements to enhance the operation of the syst
HY-RedBull-V3.0-2011.6.14
- 按键输入，演示灯亮，ARM开发板。会 hi会回家-Key demo lights
wsd_setup_v705
- AD公司Aducxxx单片机的下载软件，7.05版本，实际使用过程中，注意板子加电电压需高于5V，否则容易烧写不成功。-The AD the company Aducxxx microcontroller download software, 7.05 version of the actual use of the process, attention to the board the power voltage should be higher than 5V, or easy progra
GPIO_KEYINPUT
- STM32F103RBT6两KEY键控制LED闪烁，按键灯亮，不按灯灭-STM32F103RBT6 two KEY key to control the LED is blinking, button lights do not light off