资源列表
STM32F103C8T6核心板资料(1)
- stm32F103最小系统资料，包含原理图，简单测试代码(Stm32F103 minimum system data, including schematics, simple test code)
opencdb
- 实现EVC＋＋4.0读取cdb文件。开发环境EVC4.0，已测试通过，测试环境：EVC4.0＋PDA＋WinXPSP2 相关文件请到ESRI和微软网站获取。-achieve EVC + +4.0 read cdb document. EVC4.0 development environment, the test, test environment : EVC4.0 PDA + + WinXPSP2 related documents, visit ESRI and Microsoft
Datalogger
- 8 channel data logger the no. of sensors will be detected
MC9S12XS256RMV1
- MC9S12XS256RMV1单片机的资料,学习MC9S12XS256RMV1系列单片机必读.含有此系列单片机的所有寄存器介绍.-MC9S12XS256RMV1 SCM data, learning MC9S12XS256RMV1 MCU must read all registers containing the MCU s introduction.
my_boot(2440_UCOS_OK)
- 移植好的UCOS2.86版，能在2440上直接运行。（板的的晶振是16.9344M，用COM1来调试）-Transplantation UCOS2.86 best version that can run at 2440 directly. [The crystal plate are 16.9344M, used to debug COM1]
serial_test
- 基于AT91SAM9263 ARM920T处理器，在WINDOWS CE 5.0环境下开发的串口数据收发并显示的程序。使用EVC 4.0开发-Based on AT91SAM9263 ARM920T processor, in the WINDOWS CE 5.0 environment, the development of Serial Port bus data transceiver and display procedures. The use of EVC 4.0 Developme
vxWork_Boot-_andFlash_s3c2410
- 一个能从s3c2410的nandflash中启动的vxWorks BSP，希望能有用。-Start a from s3c2410 nandflash in vxWorks BSP, hoping to be useful.
Open407Kit-uCosETH.ZIP
- This file provides a sample code for programming Ethernet STM32F407 on Open407 Kit. At the same time we can design a similar circuit board kit STM32F407.
NXPNFC_P61_JCOP_Clients-SEAccessKit_AR7.0.3_OpnSr
- NFC eSE client source code
1
- flv的vhdl教学文件:在线调试 自己慢慢欣赏吧-flv file of VHDL Teaching: Online debug their慢慢欣赏吧
S3C44B0X
- 用的是三星的S3C44B0X，板子上有8M SDRAM、2M NOR FLASH、16M NAND FLASH、USB接口和两个串口 5-Using a Samsung S3C44B0X, board have 8M SDRAM, 2M NOR FLASH, 16M NAND FLASH, USB interface and two serial 5
CH378读写u盘程宇和相关资料
- 使用MDK5编写的程序，利用STM32F103驱动CH378模块对U盘就行读写，还包含了相关的资料(Using the program written in MDK5, use STM32F103 to drive the CH378 module to read and write to the U disk, and also include relevant information.)