- L_9320 MSP430F149驱动ILI9320程序
- HitBrick 很简单的小游戏
- aspfr_ASPX-ECOLE___Page this source code is managing a school with the different account of pupils subjects and classes
- watchdogltest Arm linux嵌入式系统下的看门狗程序代码
- Linux-TQ2440-rumrn QT的入门实例
- Program this is a programe for battery prediction system with neuralnetwork.
资源列表
1720
- ISD1700语音芯片的源程序代码，给一些需要的同事用！-ISD1700 voice chip of the source code, give a number of colleagues in need!
USB_4450_C
- pic18f4550 USB中断函数写法 与DEMO不同的是这个程序并非使用轮询法，可以使得pic18f4550用得更灵活-pic18f4550 USB interrupt function is written with the DEMO different polling method was not used in this program, you can make use of more flexible pic18f4550
DAC
- 51单片机数模转换，函数采用封装形式，主函数中直接调用就行-51 single-chip digital-to-analog conversion, the use of package functions, the main function called directly on the line
keyshow
- 主要讲述通过对按键的扫描和数码管的结合使用，来动态的显示“888888”。-Primarily about the right buttons by scanning and digital control, in combination, to dynamically display " 888888."
STC89C52_watchdog
- STC89C52RC单片机看门狗实验，该使用导致灯亮5000个时钟周期后熄灭。-STC89C52RC microcontroller watchdog experiments, the use of the lights go out after 5000 clock cycles.
kalman_filter-master
- 卡尔曼滤波C++实现代码，直接可用卡 尔曼滤波C++实现代码，直接可用-A Visual C++ program that can show the kalman filter of the data calculations A Visual C++ program that can show the kalman filter of the data calculations
adc_no
- 基于英飞凌XC886单片机的程序开发。不使用中断进行AD转换。-Infineon XC886 microcontroller based application development. Without interruption for AD conversion.
src
- 附件中是在keil for arm下编译的ARM程序——LCD万年历（暂名） 有源代码和PROTEUS文件。 刚学ARM，刚学写程序…… 所以程序写得可能垃圾，不过功能基本已实现已经设置了keil for arm与proteus（7.1）的联调，不过我基本上没用 希望大家多多指正…… 功能未完，待续…… -Attached is the keil for arm compiled ARM program- LCD calendar (tentative name) S
SourceCode02_7SEG_OK
- 5416七段数码管测试程序,很详细,值得研究-5416 Seven-Segment LED test program, in great detail, worthy of study
boyinyue
- 利用单片机设计的音乐播放器，在PROTEUS仿真环境下运行-microprocessor designed music player, in PROTEUS simulation environment running
LEDctrl
- keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc
Experiment26_sd
- 一个基于XL2000开发板的sd的应用程序-XL2000 a development board based on the application sd