CDN加速镜像 | 设为首页 | 加入收藏夹
当前位置: 首页 源码下载 嵌入式/单片机编程

资源列表

« 1 2 ... .88 .89 .90 .91 .92 17993.94 .95 .96 .97 .98 ... 33646 »
  1. adc

    0下载:
  2. 实现ADC采样芯片外的模拟电压,通过LCD显示,并通过串口(J6)发送到PC机 注:试验时把LCD电源跳线(J20_1和J20_2)联接好!-ADC-chip realization of the analog voltage sampled by LCD display and serial port (J6) sent to the PC, Note: test the LCD power supply jumper (J20_1 and J20_2) connection good!
  3. 所属分类:SCM

    • 发布日期:2017-04-06
    • 文件大小:11.6kb
    • 提供者:林辉
  1. dianlidianzijishu

    0下载:
  2. 电力电子的论述及其应用展望论述和应用前景-Discussion of power electronics and its application prospect and prospect discussed
  3. 所属分类:VHDL-FPGA-Verilog

    • 发布日期:2017-05-22
    • 文件大小:6.28mb
    • 提供者:苏海
  1. SOPC_sopccc

    0下载:
  2. fpga的初级入门资料,对学习SOPC很有帮助,呵呵!-fpga primary introductory information helpful in learning SOPC, Ha ha!
  3. 所属分类:VHDL-FPGA-Verilog

    • 发布日期:2017-05-10
    • 文件大小:2.27mb
    • 提供者:rjt
  1. 比较器CP0+来自于VREF引脚

    0下载:
  2. 此程序可完成CP0比较器的比较功能,比较器CP0+来自于VREF引脚,CP0-由S2控制.按下S3后,比较器响应后将产生中断,可在中断程序中设断点观察.-This program can be completed relatively CP0 comparator function, the comparator from the VREF pin CP0+, CP0-controlled by the S2. Press the S3, the comparator generates an
  3. 所属分类:单片机(51,AVR,MSP430等)

    • 发布日期:2017-03-28
    • 文件大小:8.52kb
    • 提供者:林辉
  1. key

    0下载:
  2. 按键测试程序.按下S1-S4,在LCD上分别显示1-4 实验时短接J17的1,2引脚(LCD电源控制引脚)-Key test program. Press S1-S4, 1-4 in the LCD display on the experiments were short the pins 1,2 J17 (LCD power control pins)
  3. 所属分类:SCM

    • 发布日期:2017-04-17
    • 文件大小:10.57kb
    • 提供者:林辉
  1. lcd

    0下载:
  2. 1602A LCD显示程序,运行程序LCD显示"BT F310 V1.0",SPI接口方式的NLSF595并行输出 控制LCD-1602A LCD display program, run the program LCD display " BT F310 V1.0" , SPI parallel interface mode of NLSF595 LCD output control
  3. 所属分类:SCM

    • 发布日期:2017-04-01
    • 文件大小:7.38kb
    • 提供者:林辉
  1. CPLD-based-Power-Three-

    0下载:
  2. 基于CPLD三相全控桥整流电源的论述和应用-CPLD-based Three-phase Bridge Converter exposition and application of power
  3. 所属分类:VHDL-FPGA-Verilog

    • 发布日期:2017-04-03
    • 文件大小:562.13kb
    • 提供者:苏海
  1. PCA

    0下载:
  2. PCA捕捉模块0的CEX0被设置在按键S3对应的引脚上,按下和松开S3,将会产生下降和上升沿信号,引发捕捉模块动作。-PCA Capture Module 0 CEX0 S3 is set the corresponding pin in the key, press and release the S3, will result in decline and the rising edge signal capture module trigger action.
  3. 所属分类:SCM

    • 发布日期:2017-04-03
    • 文件大小:3.91kb
    • 提供者:林辉
  1. MCU51-Programme-

    0下载:
  2. 整理了我自己编写的一些51单片机C语言程序,里面有数码管的代码,DS18B20的初始化,红外传感器的初始化,液晶、步进电机I^2C总线等一些程序-Written compiled some of my own microcontroller C-51 program, which has digital code, DS18B20 initialization, the initialization of infrared sensors, LCD, stepper motor I ^ 2C b
  3. 所属分类:SCM

    • 发布日期:2017-04-04
    • 文件大小:3.78kb
    • 提供者:LY
  1. Photoshop-CS5-Read-Me.pdf.tar

    0下载:
  2. Manual for Adobe photoshop CS5 extended edition
  3. 所属分类:SCM

    • 发布日期:2017-03-31
    • 文件大小:61.36kb
    • 提供者:harry
  1. MCU51-C_language

    0下载:
  2. 这是一本关于51单片机C语言的编程入门教程,很适合初学者使用-This is a single chip on 51 Tutorial C Programming Language, it is suitable for beginners
  3. 所属分类:SCM

    • 发布日期:2017-04-09
    • 文件大小:386kb
    • 提供者:LY
  1. Altera_2C35F672_FFT_Verilog.RAR

    0下载:
  2. Altera芯片2C35F672实现FFT_Verilog代码。-Altera chip 2C35F672 achieve FFT_Verilog code.
  3. 所属分类:VHDL-FPGA-Verilog

    • 发布日期:2017-04-07
    • 文件大小:463.34kb
    • 提供者:tsinsun
« 1 2 ... .88 .89 .90 .91 .92 17993.94 .95 .96 .97 .98 ... 33646 »
搜珍网 www.dssz.com

浏览历史记录

关闭