资源列表
xine_c51
- 我学习C51过程中所编的程序整理，由易到难，全部调试运行成功，现在和大家分享！-I C51 in the process of learning the procedure code order, from easy to difficult, all the debugging and running successfully, and now to share!
mpc860init
- mpc860初始化程序代码，可当做为mpc860的LOADER使用。可用它来加载操作系统。-BTF340 experimental procedure development board
xine001_keil
- 用51单片机控制AD，测量室温，并用串口上传到上位机，绘出温度曲线图。-MCU with 51 AD, measured at room temperature, and uploaded to the PC with a serial port, draw the temperature profile.
gm5766_Code
- 美国Gensis公司的液晶驱动板专用IC，GM5766是16位X86内核微控制器，程序很完整，配合屏参数据，可以出很正规的产品！-U.S. Gensis' s LCD driver board dedicated IC, GM5766 is a 16-bit X86 core microcontroller, the procedures are complete, with the screen parameter It can be a very formal product!
wenjian
- 用软件实现RTC，在每秒中断一次的中断中调用-Using software RTC, interrupts per second interruption of a call
ps2
- 本来以为模拟PS2协议相当的麻烦，今天下了一本PS2协议手册看了半天，原来读键盘值相当简单嘛，比模拟SPI、I2C简单多了呵呵。-Considerable agreement that the simulation would have trouble PS2, PS2 today an agreement under the manual looked a long time, the original value of reading the keyboard is quite simple
auto_detec_system_design
- 当LED显示屏在开启的时候，我们可以用远程控制电脑通过internet 网络来控制随屏控制电脑。再通过随屏控制电脑发送将显示屏的某几行-When the LED display in the open, we can use the remote control to control the computer through the internet network with the control computer screen. And then sent through the compu
pmw
- 基于VHDL的pmw发生器论文格式，仿真实现。word文档-pmw，VHAL，pluse width modulation generator
Infrared_Code_Reader
- 可以读取8位、13位2种类型地址码的遥控器的按键码和地址码！程序已经通过硬件调试！大家可以参考参考！-Can read 8-bit, 13-bit address code 2 types of remote control key code and address code! Procedures have been adopted by hardware debugging!
Study_IR_Remote_Control
- 资料包含源码，硬件图，红外相关资料等，本学习型红外遥控器，通过学习一次遥控器的编码，即可脱离原遥控器来遥控电器或者设备，源码很完整，严格测试过，不过由于C52的单片机RAM有限，编码缓冲区长度有限，而不同的遥控器的编码长度也不相同，对于像空调遥控器编码比较长的就会出现学习不了的情况，必须要加外部RAM作为接收缓冲区，或者换用STC的单片机，内部的RAM比较大，不用扩展，用STC还有好处就是不需要外部的eeprom来保存读取的编码，而C52需要用外部的EEPROM来保存编码，这个源码实用的AT24
5X7
- A code to drive a 5x7 display using PIC16F628
GPS-Simulator
- * When including this file in the assembly program file, all I/O register * names and I/O register bit names appearing in the data book can be used. * * The Register names are represented by their hexadecimal addresses. * * The R