资源列表
nRF905ccc
- 这是无线收发模块用C51编写不带协议可直接使用-This is the wireless transceiver module using C51 prepared without agreement can be used directly
SD_Card_Port_definition
- SD卡接口的完整规范,很详细的介绍了SD卡接口的一些知识，对于开发SD的人员是一个很大的帮助-SD card interface standard integrity, a very detailed introduction to the SD card interface knowledge, for the development of SD is a great help
cmp8x10b
- 这是一个触摸屏的资料的Ｃ语言程序用于单片机开发-This is a touch screen information on the C language program for the development of SCM
LCDC51
- //当前状态索引号//本级菜单最大条目数//按下\"回车\"键时转向的状态索引号-/ / index of the current state of / / the largest entry-level menu / / press the "Enter" key to when the state REQUEST Quotes
8x10b
- \"肇庆金鹏电子有限公司\" \"生产的中文系列液晶显\" \"示模块内含国际一二级\" \"简体汉字和半角及全角\" \"字符字库指令功能丰富\" \"使用方便标准用户硬件\" \"接口采用握手协议完全\" \"兼容一般点阵液晶模块\"-"Zhaoqing Jinpeng Electronic Company," "Chinese production of a series of liquid crystal," "
sy0606
- //***此程序为调试通过的源程序 //***由南京赛博电子有限公司提供 //***文件名:sy0606.C***// //***是51系例单片机的最小系统 //***有AT89S51/52的在线下载功能 //***IIC总线芯片为24C02,记存密码-//*** procedure adopted for the debugger source //*** Nanjing Cyberspace Electronic Limited / / *** File Name : s
time-of-day
- * This a software code module for a time-of-day clock object. * The clock may be fixed 12-hour, fixed 24-hour, or dynamically * configurable between these two types. Clock data can be accessed * as a binary number representing the number of
ccutest3
- 功能：使用CCU的4个模块，实现非对称PWM输出。 说明：将跳线器J5、J6、J27取出，J3短接到OCD端，在JP6的PWM1、PWM2、PWM3 分别测试模块A、B、C的输出，DAOUT是模块D输出经漏波后的电压。 通过跳线器J8、J9选择高频晶振6MHz。 -function : the use of CCU's four modules, achieving non-symmetric PWM output. Note : All of the jumpe
Wcstest2
- WDT功能试验。使用WDT的定时模块，实现CPU唤醒功能。 说明：CPU配置WDTE＝0、WDSE＝1/0， 将跳线器J27短接到OCA端。-Kidney function tests. Kidney regularly use the modules to achieve CPU up function. Note : CPU configuration WDTE = 0, WDSE = 1 / 0, short jumper for J27 received OCA end.
lowtest1
- 功能：由KEY1键使系统进入空闲状态，由定时器0中断唤醒； 由KEY2键使系统进入掉电状态，由KEY3键盘中断唤醒-functions : bonding KEY1 by the system to enter idle state, the timer interruption awaken 0; Key KEY2 by allowing the system to enter the state of restart from the keyboard interrupt awaken
IAPtest1
- 功能：调用IAP服务程序实现Flash ROM的读/写操作向Flash ROM地址1000H处写入10个数据，然后读出进行校验， 若校验正确，则蜂鸣器响一声-functions : IAP service program called Flash ROM read / write to the Flash ROM address 1000 H Office into 10 data, and then read out for calibration, if the calibration
theGobang
- 这是嵌入式五子棋的软件，在北京博创公司的ARM300上调试运行成功，需要ucos操作系统，用STD2.5编译器。-This is the Embedded Software 331, in Beijing Bo Company on the ARM300 debugging operation successful OUT need operating systems, with STD2.5 compiler.