资源列表
mdct.tar
- 这是06年4月刚刚完成的程序，从opencore.org下载而来。用vhdl语言描写，以及matlab仿真，testbench，以及在xinlinx上的综合。 The MDCT core is two dimensional discrete cosine transform implementation designed for use in compression systems like JPEG. Architecture is based on parallel distribut
cf_interleaver2
- interleaver即交织器，里面包含有C,VHDL,VRILOG HDL三种语言写的交织器, 包括各种各样的组合达六七十种，描写详尽，是一个难得的学习交织器的材料 -interleaver that interleaver, which contains C, VHDL, VRILOG HDL three languages to write the interleaver, including a variety of combinations to depend species,
Shifters_vhdl
- -- Title : Barrel Shifter (Pure combinational) -- This VHDL design file is an open design you can redistribute it and/or -- modify it and/or implement it after contacting the author -- You can check the draft license at --- Title : Barrel Shift
DCT_vhdl
- IDCT-M is a medium speed 1D IDCT core -- it can accept a continous stream of 12-bit input words at a rate of -- 1 bit/ck cycle, operating at 50MHz speed, it can process MP@ML MPEG video -- the core is 100％ synthesizable-IDCT-M is a medium speed
DaFilter
- /* This program generates the DApkg.vhd file that is used to define * the DA filter core and gives its parameters and the contents of the * Distributed Arithmetic Look-up-table \"DALUT\" according to the DA algorithm-/ * This program generate
binary2bcd
- This build is for developing a \"binary-to-BCD\" converter for use in // displaying numerals in base-10 so that people can read and interpret the // numbers more readily than they could if the numbers were displayed in // binary or hexadecimal
SINE_SIGNAL_generator_base_on_Single_Chip_Micyoco.
- 以SPCE061A单片机（ Single Chip Micyoco）为核心，通过DDS合成技术设计制作了一个步进值能任意调节的多功能信号源。该信号源在1KHz～10MHz范围能输出稳定可调的正弦波，并具有AM、FM、ASK和PSK等调制功能。信号输出部分采用低损耗电流反馈型宽带运放作电压放大，很好地解决了带宽和带负载能力的要求。系统带中文显示和键盘控制功能，操作简便，实现效果良好。 内含 原程序，正弦信号发生器的pCB原理图，以及一些相关论文。-to SPCE061A (Single Ch
RS232-CAN
- 用Freescale的8位单片机做的RS232-CAN的通讯转换板.包含固件程序,原理图,PCB图和一个说明文件.-with Freescale's 8-bit MCU do RS232-CAN communication switch plate. Includes firmware procedures, drawings, PCB map and a note.
Dimmer_code
- AT89C2051模拟PT2262，3M晶振，经实验稳定可靠 -AT89C2051 simulation PT2262, 3M Oscillator, reliable experimental
CLOCK_n1
- Em78p447四位数LED DISPLAY计时,累加/倒数/闹铃/时钟/-Em78p447 four-digit LED DISPLAY time, the cumulative / countdown / alarm / clock /
rtl8019_vxworks
- 是vxworks下的网卡芯片RTL8019驱动，在S3C44B0下可运行。-is vxworks chip card under the RTL8019 driver, in S3C44B0 under operational.
armTeach
- 上此程序的源代码，偶花了好多心血才能写出来的，请各位EVC友们多关注-on this program's source code and even spent a lot of effort to write, please remember to pay more attention EVC