资源列表
SRC
- 热量表通用程序，检测水管流量和进水管-出水管温度差，用于热量的累积。-The general program of heat meter, water flow and the water inlet pipe detection- outlet temperature difference for heat, accumulation.
081104
- 使用义隆低成本单片机的感应灯程序，专用于保险箱内，低功耗。当保险箱打开时提供光源和发出感应信号-The use of Elan low cost microcontroller induction lamp program, dedicated to the safe, low power. When the safe is opened to provide light source and sends an induction signal
SOURCE
- 门禁系统单元门口控制系统，提供与每个房间的485呼叫通信，控制单元门的开关和管理-Access control system units gate control system, and each room provides 485 call communication, switching and management control unit door
source
- 温度仪表通用程序，可检测热电偶和CU50。程序带有PID控制算法和PID参数自整定算法。-General procedure can detect the temperature meter, thermocouple and CU50. The program with a PID control algorithm and the PID parameters self-tuning algorithm.
SRC
- 用三星单片机写的电热毯控制程序，有数码管显示温度，有温度控制功能和定时功能，已批量使用。-Using Samsung MCU write blanket control program, there are digital display of temperature, temperature control function and timing functions, have been used in batches.
7segment
- THIS IS A PROGRAM FOR 8051 ON LIEL SOFTWARE TO ACCESS 7 SEGMENT AND DISPLAY DESIRE NUMBERS ON 7 SEGMENT DISPLAY. IN 7 SEGMENT, 8 LED ARE RESPONSIBLE FOR DISPLAYING ANY NUMBER WHICH ARE CONTROLLED BY MICROCONTROLLER. YOU CAN USE THIS LOGIC ON MANY OTH
nor_flash_core
- Verilog实现的NOR FLASH控制器，基于M25P128开发，功能完整，简洁易懂，自用无问题。-Verilog implementations NOR FLASH controller, based M25P128 development, full-featured, easy to read, for personal use, no problem.
jsq
- 基于FPGA的计算器，可以实现加减乘除运算功能，由于时间问题，浮点运算未能实现，其中的二进制与BCD码相互转换的模块可以使用-FPGA-based calculator, arithmetic calculation function can be achieved, due to time issues, floating-point operations failed to achieve, including binary and BCD code conversion modules t
M25P128_model
- M25P128（NOR FLASH）的仿真模型，Verilog实现，调试了很久才通，现在基本功能完整，仿真时打印调试信息，自用无问题。-M25P128 (NOR FLASH) simulation model, Verilog implementation, commissioning a long time to pass, and now the basic functions of a complete, print debug information during simulation,
i2c_slave
- Verilog实现的i2c从设备仿真模型，只需修改控制码就可直接使用，自用-Verilog implementations i2c slave device simulation models, simply modify the control code can be used directly, for personal use
usb_sim_model
- EZ-USB的仿真模型，Verilog实现，能够实现端点传输，自用。-EZ-USB simulation model, Verilog implementation, to achieve the endpoint transmission, personal use.
num-_change
- 用汇编编写的进制转换器。16进制、10进制和二进制之间相互换算，二进制有LED灯显示，有超量程报警功能，有功能提示（LED数码管），基于C8051F310 -Written in assembly hex converter. Hexadecimal, mutual conversion between decimal and binary, with LED lights display, there is over-range alarm function, a function pro