资源列表
electronic-clock-source-program
- 1602+18B20+DS1302电子时钟源程序 按K7按键进入设置状态 按K6按键设置时的 数值+ 按K5按键设置时的 数值--1602+ 18 b20+ DS1302 electronic clock source program Press K7 button to enter setting state Push the K6 numerical+ Settings According to the numerical- K5 butto
1602-LCD-clock
- 功能完整的1602LCD时钟实验 //按K1按键进入设定状态 //按K2,依次进入闹钟功能是否启用，闹钟时,分秒,年,月,日及时间时,分,秒的设置,直到退出设置状态 //按K3,调整是否起用闹钟和调节闹钟时,分,秒,年,月,日,时间的时,分,秒的数字 //LCD第二排中间显示小喇叭，表示启用闹钟功能，无则禁止闹钟功能（可在调整状态进行设置） //正常状态,LCD上排最前面显示自定义字符,LCD下排最前面闪动 RICHMCU //设置状态,LCD上排最前面显示 P ,下排
PWMControl-LED-lights
- PWM控制LED灯渐亮渐灭实验 // 按K1，PWM值增加，则占空比减小,LED 灯渐暗。 // 按K2，PWM值减小，则占空比增加,LED 灯渐亮。-PWM control LED lights gradually fade out the experiment //by K1, PWM value increases, the duty ratio is reduced, LED lights are dimmed. //by K2, PWM value decreases,
LEDRunning-water-light-code-briefly
- 简要流水灯代码，不过里面端口不同，出来的效果不同-Briefly water lamp code, but the inside port is different, the effect is different
CAN_Filter_test_2
- 工程实现CAN验收滤波，LPC2194处理器实现CAN验收滤波，直接收与设置ID向符合的消息，已用USBCAN调试通过，已应用。-The project is CAN Filter acceptance with LPC2194. The project is tested successfully with USBCAN.
balance_car_xs_V1.2.5
- 基于飞思卡尔MC9S12XS128处理器的自平衡车代码，有线性CCD的自创的动态自适应阀值算法，模糊PID,自创速度滤波，无线模块，LED小屏显示，等等。稳定性好。-Freescale processor-based MC9S12XS128 self-balancing vehicle code, there are linear CCD dynamic adaptive threshold algorithm homemade, fuzzy PID, homemade speed filter
MY_I2C_TEST
- LPC2194处理器，外扩E2PROM，工程用 I2C实现对E2PROM的读写操作，I2C采用中断的方式实现，已调通，已在项目中使用。-The processor LPC2194 with E2PROM.The project uses I2C with interrupt to write and read the E2PROM.
LPC1768-Breathing-Led
- 对恩智浦公司的LPC1768通过定时器制作呼吸灯，已经测过，完全可以使用。-NXP s LPC1768 breathing light produced by a timer, had been measured, can be used.
0-example_test_board_x
- 本板共有5个LED， 其中D1是板载3.3V指示灯； D2-D5是FPGA的IO口控制；在上电烧录程序后， D1点亮表示电源正常； 其余4个LED依次能够点亮表明硬件完好。-This Board consists of 5 LED, where D1 is the onboard 3.3V indicator D2-D5 FPGA IO mouth control power on after-burning program, D1 point light indicates that pow
sp605_IBERT_rdf0036_13.3_c
- 此文件是用所需的时钟缓冲器岁设计示例顶部包装。用户逻辑可以在此包装和岁设计实例化。XILINX官方参考设计。-This file is an example top wrapper for the ibert design with the required clock buffers. User logic can be instantiated in this wrapper along with the ibert design.
qthualingde.tar
- 主要实现动态曲线
MCP410
- 基于单片机的MCP410数字电位器的C语言实现，通过KEIL平台编程，编译。-MCP410 microcontroller based digital potentiometer C language programming platform by KEIL compiler.