资源列表
DK07_YCDZ
- 无人机地面遥测接收站源码，基于AT89C2051，接收无人机下行的状态数据，同时解析GPS数据，送给主控显示-UAV ground station telemetry source, based on AT89C2051, UAV downlink receiving status data, and GPS data analysis, and gave master display
rwbm
- 无人机任务转发功能板源码，基于AT89C2051，通过串口接收任务指令，并口输出给主控-UAVs forwarding board source, based on AT89C2051, task instructions received through the serial port, parallel port output to the master
WK
- 无人机外操纵器控制源码，基于AT89C2051，汇编语言，实现按键编码后通过串口发送给无线收发器，对无人机控制-UAV external manipulator control source, based on AT89C2051, assembly language, to achieve key encoded through the serial port to the wireless transceiver, control of the UAV
PWM
- FPGA产生PWM波控制小车，Verilog语言编写，实现简单的正、反、停控制-FPGA generate PWM wave to control the car, Verilog language, to achieve a simple positive and negative, stop control
1
- 实现智能小车左右避障，以完成小车走迷宫部分的功能-About smart car obstacle avoidance, in order to complete the car maze part of the function
EX06_WDT
- 这是一个TMS320VC5509A使用看门狗定时器的范例，示范了如何设置看门狗定时器，如何更新看门狗定时器以及如何对看门狗定时器超时的响应，利用超时响应产生中断并作出响应-This is an example of using the watchdog timer TMS320VC5509A demonstrates how to set the watchdog timer, watchdog timer, and how to update how the response of the w
EX04_EXINT
- 这是一个TMS320VC5509A的外部中断的使用，示范了如何设置中断向量表，如何打开中断，关闭中断，以及全局中断向量的一些设置，并展示如何接收外部中断，并对外部中断作出响应-This is an external interrupt TMS320VC5509A use, demonstrates how to set the interrupt vector table, how to open an interrupt, disable interrupts, as well as some
EX03_RTC
- 这是一个TMS320VC5509A的内部实时时钟的使用，示范了如何对内部时钟进行配置，以及如何写入时间，读取时间，并利用实时时钟产生中断，作出中断响应-This is an internal real-time clock TMS320VC5509A use, demonstrates how to configure the internal clock, and how to write time, read time, and use the real-time clock interru
EX02_TIME
- 这是一个TMS320VC5509A的使用和开发定时器的程序，示范了如何配置内部定时器的使用，以及如何利用定时器产生中断并作出中断响应-This is a TMS320VC5509A the use and development of the timer program that demonstrates how to configure the internal timer, the timer interrupt is generated and how to use and make th
EX07_AD
- 这是一个简单的TMS320VC5509A的片内内置AD的设置和读取数据的程序，从中可以学习与AD相关的CMD文件的编写以及如何设置片内AD工作状态，采样频率等这些参数，以及如何读取AD转换后的数据-This is a simple built-in AD TMS320VC5509A chip set and read data procedures associated with AD can learn from the preparation of the CMD file and how
NRF24L01_uasrt
- 板子通过USB加电后，先向串口1输出一串测试数据，然后USB被PC识 别出来，虚拟出一个串口号给这个USB设备，此时可以通过在PC端的串口助手类 软件选择该串口号。-The board is powered via USB they ask a bunch of test data output port 1, and then identified by PC USB, a virtual serial port number to the USB device, this time
AD
- stc89c51单片机控制程序，通过4路AD采集模拟电压，并在液晶1602上显示电压值-stc89c51 MCU control procedures, through the four-way AD acquisition of analog voltage and the voltage value displayed on the LCD 1602