- 3 在实时跟踪系统中
- spsmd 图像的平面微分平方和能够反映图像高频分 量的能量
- conversationscope J2EE中使用conversation scope的样例代码
- nilai rekap pkl teknik informatika universita islam syarif hidayatullah jakarta semester 7 angkatan 2014
- surat permohonan pkl spp pkl teknik informatika universita islam syarif hidayatullah jakarta semester 7 angkatan 2014
- Surat_keterangan_Selesai_PKL SKL pkl teknik informatika universita islam syarif hidayatullah jakarta semester 7 angkatan 2014
资源列表
Traffic-lights
- 基于89s51单片机的十字路*通灯,包括proteus仿真图，数码管显示等-Based on the 89 s51 microcontroller of crossroads traffic lights。Including the proteus simulation diagram, digital tube display, etc
ad7665pll
- AD7665的控制程序，8路AD穿行，到FPGA中进行了并行转换，16位模式，从模式-AD7665 control program, AD through 8 road, into the FPGA parallel conversion, 16 bit pattern from the pattern
3583.LaunchPadFirmwareUpdater
- software update for ti launchpad
ida_msp430_v12.ZIP
- msp430 decompiler module v 12 for IDA disasemble
ZNetCom-Utility
- 中兴网络模块配置软件，可以实现对网络模块的计时配置，了解物联网的应用知识的-The The ZTE network module configuration software, can achieve timing configuration of the network module, for the application of knowledge of the Internet of Things
Temperature_test_labview
- Temperature_test_labview,基于labview的温度检测与显示应用，可以实现动态显示功能-Temperature_test_labview labview-based temperature measurement and display applications, you can achieve a dynamic display function
hui_bian_chengxu
- hui_bian_chengxu,汇编程序应用各种应用程序，可以了解程序的的底层运作的-hui_bian_chengxu assembler application in a variety of applications, can learn about the program s underlying operations
lab21-TCP
- TCP协议源代码，基于RL8019网卡芯片，亲自测试可以使用-TCP protocol source code, based on the RL8019 chip card personally test can be used
Pump_Control
- 通过网络模块进行办公室远程控制水泵开关以及上床压力值，实现远程办公自动化的 -Office to remotely control the pump switch module through the network, and go to bed pressure value, remote office automation
MC9S12XS128
- 本程序是飞思卡尔单片机常用的程序片段及部分程序事例，知识点-very good
ethernet
- 一个简单的嵌入式程序-a simple procedure Embedded -a simple procedure Embedded
watch-dog
- XEP100：当用户程序“跑飞”，看门狗产生一个强制系统复位。为了阻止看门狗复位，用户程序 必须定期的复位COP计数器。通过向COPCTL寄存器中写入0x00可以关闭看门狗。单片机复位 后的默认状态看门狗是关闭的。设置COPCTL寄存器可以设置看门狗的延迟周期。在COPCTL 设置的周期时间内，向ARMCOP寄存器先后写入0x55和0xaa，将清除COP看门狗定时器，但 不会对寄存器内容造成影响。向ARMCOP中写入除了0x55和0xaa的任何值将导致系统的复位。-XEP100: