资源列表
ucos--lamdbatools
- windows下ucos-ii 开发环境lamdbatools 配置，操作过程-ucos-ii under windows the development environment lamdbatools configuration, operation
Coffee-machine-with-HT48R06
- HT48R06的智能咖啡机设计，包含软硬件设计说明。-Coffee machine coffee machine, do with HT48R06 microcontroller.
mcuelf
- 单片机小精灵最新版,支持STC1T单片夹,破解了拿出来给大家分享-Microcontroller elf latest version support STC1T monolithic folder, cracked out to share
MI_CR
- 以前发现的一款电脑声卡示波器软件,发现还不错,就破解了,在这里在这里分享给大家,软件是虚拟示波器-Multi-Instrument3.2-Previously found a computer sound card oscilloscope software, found a pretty good crack share here for everyone here, the software is a virtual oscilloscope-Multi-Instrument3.2
abc
- 用VERILOG编写的FPGA控制vga显示的源码-FPGA control the vga display the source code written in VERILOG
5.guanggaodeng_qubiao
- 利用取表的方法，使端口P1做单一灯的变化：左移2次，右移2次，闪烁2次（延时的时间0.2秒）。-Take the table, do a single lamp port P1 changes: left, right by 2 flashes 2 times (delay time of 0.2 seconds).
4.-guanggaodengdezuoouyi
- 做单一灯的左移右移，硬件电路如图4.4.1所示，八个发光二极管L1－L8分别接在单片机的P1.0－P1.7接口上，输出“0”时，发光二极管亮，开始时P1.0→P1.1→P1.2→P1.3→┅→P1.7→P1.6→┅→P1.0亮，重复循环。-Shift left shift right, do a single lamp hardware circuit as shown in Figure 4.4.1, eight light-emitting diodes L1-L8 respectively
3.duolukaiguanzhuangtaizhishi
- AT89S51单片机的P1.0－P1.3接四个发光二极管L1－L4，P1.4－P1.7接了四个开关K1－K4，编程将开关的状态反映到发光二极管上。（开关闭合，对应的灯亮，开关断开，对应的灯灭）。-AT89S51 microcontroller connected to P1.0-P1.3 four light emitting diodes L1-L4, P1.4-P1.7 pick up the four switches K1-K4 programming the switch status
2.monikaiguandeng
- 监视开关K1（接在P3.0端口上），用发光二极管L1（接在单片机P1.0端口上）显示开关状态，如果开关合上，L1亮，开关打开，L1熄灭。-The monitor switches K1 (connected to the the P3.0 port on), light-emitting diode L1 (connected to the microcontroller on the P1.0 port) display switch status, if the switch is clos
DS18B20-temperature-measurement
- 基于DS18B20的单片机开发程序，给出了详细的C语言代码，以及详细的C语言注释-DS18B20-based microcontroller development program, given the details of the C language code, and the C language comments
NLmeansfilter
- Implementation of the Non local filter for image denoising
lcd1602_04
- 51单片机读写DS18B20的温度，通过单总线时序进行编程,在lcd上显式出来-51 SCM reader DS18B20 temperature programmed through a single bus timing, explicitly come out in the lcd