资源列表
2-key-recognition-and-LED-indicator
- 硬件环境： 按键：Key1--PD2 Key2--PD3 （低电平表示有按键按下） LED：LED1~LED8--PC0~PC7； （LED在高电平被点亮） 功能：当Key1按下时，所有8个LED的均被点亮 当Key2按下时，所有8个LED均被熄灭-Hardware environment: Key: Key1-PD2 Key2-PD3 (low level said keys pressed) LED: LED1 ~ LED8-PC0 ~ PC7 (L
SD-card-bottom-drive
- 本例程提供了大量SD卡的底层驱动函数，并经过测试为成功 串口波特率：96-This routine provides a number of the ground floor of SD card function drivers, and after test for success Serial baud rate: 9600
RTC-set-the-clock-and-display
- RTC时钟源为外部低速时钟，且外部低速时钟源的64分之一Tamper引脚（PC.13)上输出。 通过秒中断功能，在LED1(GPIO_Pin_0)上以2s为周期闪烁，并以1s为周期通过USART送出时间信息 （在串口调试软件上以24小时时间制显示） USART1设置：波特率：9600 数据位：8 停止位：1 奇偶校验位：无 硬件流控制：无 注：编译时，Library Configuration应选为FULL，以使C库函数fputc映射到U
lights
- STM32流水灯实验程序，三盏灯轮流点亮。基于keil4编程器。-lights on stm32
SmartFusion-series
- SmartFusion系列串口实验及实验教程-The SmartFusion series serial experiments and experimental tutorial
GPIO
- STM32入门程序，可以下载来看看。关于GPIO管脚的- STM32 Starter program, you can download to look at. GPIO pins
3.2LCD
- 3.2寸触摸屏 显示及触摸 基于stm32f103vc 驱动芯片ADS7843-3.2寸触摸屏 显示及触摸 基于stm32f103vc 驱动芯片ADS7843
lpc2138
- lpc2138/lPC2148 adc采样及串口发送-lpc2138/lPC2148 the adc sampling and serial port to send
diyijiang
- 稀里糊涂学stm32系列，第一讲内容，相对于手册，学习起来更容易上手，暂时只有6讲，均上传。-Sleepwalk learn stm32 series, talk about content, relative to the manual, learning is easier to get started, for the time being only 6 speak, are uploaded.
dierjiang
- 稀里糊涂学stm32系列，第二讲内容，相对于手册，学习起来更容易上手，暂时只有6讲，均上传。-Sleepwalk learn stm32 series, talk about content, relative to the manual, learning is easier to get started, for the time being only 6 speak, are uploaded
disanjiang
- 稀里糊涂学stm32系列，第三讲内容，相对于手册，学习起来更容易上手，暂时只有6讲，均上传。-Sleepwalk learn stm32 Series Lecture content, as opposed to the manual to learn it more easy to use, temporarily speaking, are uploaded.
disijiang
- 稀里糊涂学stm32系列，第四讲内容，相对于手册，学习起来更容易上手，暂时只有6讲，均上传。 -Sleepwalk learn stm32 series, talk about the content, as opposed to the manual to learn it more easy to use, temporarily only six stresses are uploaded.