资源列表
S3C2440A
- S3C2440 IAR 针对ARM920T工程. jlink未破解只好用IAR 对 ARM V4T 版本的都有帮助.-S3C2440 IAR for the ARM920T works. Jlink no choice but to use cracked versions of the IAR right ARM V4T be helpful.
CalcCRC
- CalcCRC8 The CalcCRC8 is used to append an eight-bit CRC to the message. A successful CRC check results in returning a 0. Implementation: This CRC will be using the CRC-16/CITT protocol. A 16-bit wide non-reflected code that starts initially
rtc
- Ｉ２Ｃ总线的ＲＴＣ源码，支持３５３９０，４３３７，１２０８，１２０５-I2C bus RTC source code, support 35390,4337,1208,1205
lwip-1.4.0.rc1
- Lwip1.14在S3C2440上，非操作系统的移植，网络芯片为cs8900。开发工具为MDK4.0。经过验证通过。-Lwip-1.14 ports on the S3C2440 whith NO OS, net driver is CS8900. Development tools for the MDK4.0. Validated through.
STM32F107
- 基于STM32F107网络编程的完整项目源代码，包括tcp/ip，efsl等等。-Network programming based STM32F107 complete project source code, including the tcp/ip, efsl so.
ILI9327_Example
- 基于ILI9327这款LCD控制器的液晶屏驱动程序，由STM32驱动-This LCD controller based ILI9327 LCD driver, driven by the STM32
Lm1138-SPI-IO-simulation
- st的微机械陀螺L3G4200D驱动，调试板为lm3s1138，模拟SPI方式-st micro-gyroscope L3G4200D drivers, debug board is lm3s1138, simulation SPI mode
arm-rvds2.0_2
- ARM RealView开发工具包是一套完整的、高性价比开发调试工具，用于半导体通用32位微控制器（MCU）产品。本工具包以ARM RealView Developer Suite全球领先的16/32位嵌入式RISC微处理器解决方案厂商ARM近日针对采用Intel( XScale(技术的网络基础设施、无线和存储设备，推出ARM(r) RealView(开发工具组。该工具组提供最佳编码生成功能，同时可降低开发成本。作为唯一支持所有顺应ARM结构的Intel Xscale处理器的工具组，RealVi
ATMEGA256
- atmega256英文资料，可以替代ATMEGA128并增加FLASH容量，而不需要更换-English atmega256 information can FLASH alternative ATMEGA128 and increase capacity, without the need for replacement
AT91SAM7S-libs-and-axample-spi-mmc16MB
- AT91SAM7S mmc card spi mode libs
STM32_USART1
- stm32 库文件：3.10 本程序是使用UART1接收中断,收到数据后直接把原数据从USART1发回去 一开机时,会发送 "Starting....."到USART1-stm32 Library: 3.10 This procedure is to use UART1 receive interrupt, received data directly to the original data sent back from USART1 A start,
ads1241
- ADS1241 ADS1241的程序-ADS1241 ADS1241 procedures