资源列表
stm32-usart
- STM32F103RBt6的串口通讯例程，采用寄存器方式实现。-STM32F103RBt6 serial communication routines, achieved register.
51mcuad9850
- 基于51单片机和AD9850芯片的DDS程序，通过LCD1602显示频率波形，步进可调，已经硬件调试成功-51 microcontroller and AD9850 chip DDS program, through the the LCD1602 display frequency waveform, step adjustable, has hardware debugging
PID
- 单片机通过PWM输出供电，驱动3个串联电阻，其中50K是一个电位器，人为不断的旋动电位器，来模拟负载无规律的变化。 目标要求：100uF电容两端的电压不受负载的影响，即ADC读数要求稳定在100左右。 大概的输出电压mV = 5000mV * ADC读数 / 255 调整 P、I、D 这三个系数，还有调整间隔检测时间，即可调整负载电压的稳定度和皱纹度。 -单片机通过PWM输出供电，驱动3个串联电阻，其中50K是一个电位器，人为不断的旋动电位器，来模拟负载无规律的变化。 目标要
STC51-download
- STC51单片机 免断电下载程序 演示流水灯-The STC51 microcontroller, no-power-reset download, the program demonstrates led change
DS18B20_LCD
- 采用51单片机 处理温度传感器DS18B20的数据，并用lcd显示，已经实验成功 附仿真源文件 -51 microcontroller data processing temperature sensor DS18B20,and useing lcd display, it has been tested and verified successfully by experiment, and attached simulation source file.
C51_DS18B20_LED_Sim
- 采用51单片机 处理温度传感器DS18B20的数据，并用8位LED显示，已经实验成功 附仿真源文件-Using 51 microcontroller to manage temperature sensor DS18B20,and using led display, it has been tested and verified successfully by experiment, and attached simulation source file.
DS1302_8_led_C51_sim
- 采用51单片机 处理时钟芯片DS1302的数据，并用led显示，已经实验成功 附仿真源文件-Using 51 microcontroller to manage clock chip DS1302,and using led display, it has been tested and verified successfully by experiment, and attached simulation source file.
DS1302_LCD1602_C51_SIM
- 采用51单片机 处理时钟芯片DS1302的数据，并用lcd1602显示，已经实验成功 附仿真源文件-Using 51 microcontroller to manage clock chip DS1302,and using lcd1602 display, it has been tested and verified successfully by experiment, and attached simulation source file.
ourdev_531827
- 用链表实现LCD多级菜单显示效果，用链表实现LCD多级菜单显示效果-List LCD multi-level menu display, display LCD multi-level menu List
VB
- 通过串口来控制小车，同时有钩子函数。可以模拟按键。-Through the serial port to control the car, while the hook function. Can simulate keystrokes.
C8051F060
- c805f060单片机编程资料，包括芯片的各个模块，很实用。-c805f060 microcontroller programming information, including the various modules of the chip, very practical.
CC2530DB
- zigbee 2530 通过串口向协调器发命令 控制终端节点LED亮灭-zigbee 2530 coordinator through the serial port to send commands to control the LED light off terminal node