资源列表
MP28GA
- 基于单片机的MP28GA步进电机原理及程序-Stepper motor based on single chip MP28GA principle and procedure
CoolingSystemforcpu
- 毕业设计做的基于单片机的计算机箱温度智能监控系统-Graduation based on single chip computer to do box temperature smart control system
51MCUIRDECODER
- 51单片机红外解码，串口发送键码，方便使用。-51 MCU IR decoding, serial key code to send, easy to use.
12864
- 12864的驱动程序，已调通。 自己写的，绝对原创。-12864 drivers, have been transferred through. Write your own, absolutely original.
c51_helloworld
- 这是一个单片机89c51 helloWorld演示程式,让P1口的灯按顺序点亮或熄灭-This is a microcontroller 89c51 helloWorld demonstration program to allow P1 port lights lit or extinguished by order of
pwm
- 利用定时器产生PWM，了解原理和使用方法 硬件要求：直流电机 定时器 试验现象：按键调速，PWM部分显示速度档位，电机根据档位调节速度 这个需要把电机驱动输入端和PWM端连接起来-Generated using the timer PWM, understand and use principles of hardware requirements: DC timer test phenomenon: key speed, PWM part of the display speed ge
dianzizhong
- 1 脚接+5V 2，3脚32768HZ晶振 4脚接地 5脚接S51的P02 6脚接S51的P01 7接S51的P00 8脚接后备电源，可以接老计算机主板上的3.6V电池，也可以通过二级管隔离接一个大容量电解电容 电压在2.5V以上即可维持 按键说明：1. 共三个键，低电平有效 2. P04 和 P05 同时按：初始化 3. P06 端口按键：选择要调整的项目 4. P05 端口按键：增加；P04端口按键：减少 [注:AT89S51使用12M晶振]-A pi
fengmingqi5.18
- 用89C51玩蜂鸣，利用单片机的I/O引脚以延时方式产生方波，进而使蜂鸣器发声。注意当中用了P2_7做开关，下载完成后还需要按下这个键才能发声-Play beep with 89C51, using MCU I/O pins to produce a square wave delay means, and thus make the buzzer sound. Note which took P2_7 do switch, the download is complete press the
jianpanduogengneng
- 使用一个开关键K1作为输入信号，控制P1输出端的8个LED，实现4种变化效果，简称一键多功能控制-Use a open key K1 as the input signal, the control output 8 P1 LED, 4 changes to achieve results, referred to as a key multi-function control
clock
- 使用c和汇编语言，在C61单片机实现的语音电子钟。-Using c and assembly language, the voice in the C61 MCU clock.
jiuhuchechesheng
- 通过软件延时，使P3.4引脚输出两种信号，1kHz和2kHz频率，并且每隔一秒变化一次，交替进行。开关K做发声控制。-Software delay to P3.4 pin output two signals, 1kHz and 2kHz frequency, and changes every second time, alternately. Voice control switch K to do.
ww
- 用c和汇编编写的，在c61单片机上实现录放音功能。-With c and compilation prepared in c61 microcontroller to achieve sound recording function.