资源列表
CANsja1000_RXTX_definereg
- 这是一个用单片机控制CAN总线芯片SJA1000传输的C51程序,89C51单片机,sja1000.h是内部寄存器的定义,main.c是传输主程序-MCU control chip SJA1000 CAN transmission C51 procedures, 89C51 microcontroller, sja1000.h internal register is the definition of transmission main program main.c
TcpIP_C51+8019+RS232
- 这是一个用单片机控制网卡传输的程序,集成了TCP/IP协议,使用硬件为89C51+RTL8019,另外传输另一端是计算机串口,可以方便的实现数据验证-This is a card with SCM transmission control procedures, integration of the TCP / IP protocol. the use of hardware for 89 C51 RTL8019, and the other end is transmitting comput
basedon_SN8P1706_induction_cooker
- 功能有：功能模式选择，功率调节，定时，LED指示灯，无锅具检测，小物件检测，超温保护，干烧保护，过流过压检测，2小时自动关机功能，故障报警检测及保护代码-function : Function mode selection, power conditioning, regular, LED indicator light, no pans detection, detection of small objects. Over-temperature protection, and dry pro
demo2020
- 本程序是利用MDT2020单芯片开发的一个跑马灯程序的应用，采用一个按键输入选择不同的方式点亮LED灯-use of this procedure is MDT2020 development of the single-chip, a Bomadeng application procedures, keystroke input using a choice of different ways to light up the LED lights
armok0194327
- ds18b20上位机VB源码 ds18b20上位机VB源码-ds18b20 PC VB source ds18b20 PC, VB source ds18b20 VB source crew
AP0610-RECEIVE
- 定时器，时间一到就关闭从机开关，2、倒计时间，用于计算产品寿命，当到计数为0天时，产品停止工作-timer, a time of the closure from the plane switch, two, the countdown, the products used in the calculation of life expectancy, When the count to 0-4 days, the product stopped working
AP0610-Sender
- 软件编写RF发射，接收程式。搭配一组RF模块实现无线遥控功能。全系统低功耗设计。增加SLEEP模式最大限度节约用电 -software development, RF transmitter and receiver programs. Mix a group RF Module wireless remote control function. System-wide low power design. SLEEP mode to increase the maximum to conse
dianyundoudaifengmingqi
- 电熨斗带有源蜂鸣器输出，具有传统电熨斗的温度控制等，更人性化-electric irons with a buzzer source output with the traditional electric irons temperature control, more humane
bh1415
- bh1415驱动，可预置发射频率，开发软件Keil uVision3-bh1415 Drivers can launch preset frequency, software development Keil uVision3
avrcc
- AVR单片机的几种C语言进行比较，并进行对比-AVR several C language, and contrast
stepperctrl
- 步进电机控制程序，采用C语言编写，根据需要调用了汇编语句-stepper motor control procedures, using C language, according to the needs of the compilation statement calling
Cremote
- 51单片机接受红外遥控的C语言源码，可应用电视遥控器-51 infrared remote control microcontroller to accept the C language source code that can be applied to TV remote control