资源列表
led
- 实验班上电时，数码管不显示，顺序按下矩阵键盘后，数码管上依次显示0~F，六个数码管同时静态显示即可。-Experimental class power, the digital tube does not show the order of matrix keyboard is pressed, the digital tube followed by 0 to F, six digital tube and static display can.
ad
- 用单片机控制ADC0804进行数模转换，当拧动实验板上A/D旁边的电位时，在数码管的前三位以十进制方式显示出A/D转换后的数字量（8位A/D转换后数值在0~255变化）。-SCM ADC0804 digital to analog conversion, when the twist on the experimental board next to the A/D potential, the top three digital tube shown in decimal, digital A
da
- 用单片机控制DAC0832芯片输出电流，让发光二级管D12由灭均匀变到最亮，再由最亮均匀熄灭。在最亮和最暗时使用蜂鸣器分别警报一声，完成整个周期时间控制在5S左右，循环变化。-DAC0832 chip microcontroller to control the output current, light emitting diode D12 from off the uniform change to the brightest, and then goes out from the brig
1602
- 实现1602第一行从左侧移入“Hello everyone!”同时第二行从右侧移入“Welcome to here!”，移入速度自定，然后停留在屏幕上。-1602 The first line moved from the left side of the " Hello everyone!" While the second line from the right side moved to the " Welcome to here!" , Moved to
STM32_CAN
- 基于STM32的CAN程序，可移植到相关项目使用-CAN program based on the STM32, portable
STM32_I2C
- 基于STM32的I2C实验，调试成功，可移植使用-Based on the STM32 I2C experiment, the successful commissioning, portable use
STM32_USB
- 基于STM32的USB实验，移植时需要修改相应部分-Need to modify the corresponding part of the STM32 USB-based experiments, the time of transplantation
80C51-NRF24L01
- 基于80c51的NRF24L01发送和接收程序（1602 ds18b20 循迹小车）-80C51 NRF24L01 send and receive procedures (1602 Ds18b20 tracking dolly)
LCDxianshi
- 本设计主要是接收由键盘Data线发送过来的11位串行数据。用的是11位移位寄存器的基本原理。实现将由键盘发送过来的键盘扫描码转换成ASCII码，并在LCD1602液晶上显示出来。 -This design is to receive 11 serial data sent from the Keyboard Data line. Is the basic principle of the 11-bit shift register. Will be over the keyboard to se
t0_push_1khz
- 单片机实例程序：用定时器0中断方式产生1KHz频率占空比为 70的方波-SCM example program: use timer interrupt 0 1 KHz frequency can make of empty for 70 square wave than
NRF905-wireless-temperature-
- 基于80c51的NRF905无线温度采集程序（数码管 Ds18b20 ）-NRF905 wireless temperature collection procedure (bidirectional). Zip
SI4432--80C51
- 基于80c51单片机的SI4432 433M的无线发射芯片的c程序hex程序 最大传输距离1500米·-Based on the 80C51 microcontroller the SI4432 433M wireless transmitter chip c program hex program the maximum transmission distance of 1500 m