资源列表
clock-out
- msp430,时钟源选择调试程序，msp430时钟信号有三种：MCLK、SMCLK和ACLK。-Descr iption: Output buffered MCLK, SMCLK and ACLK.
Flash
- msp430F149,实现msp430F149内部Flash存储器的写入和擦出。-Descr iption: This program first erases flash seg A, then it increments all // values in seg A, then it erases seg B, then copies seg A to seg B.
HFXT
- msp430F149,说明：正确选择外部HF XTAL MCLK所表现出的第一个轮询XTAL OSC故障，直到稳定 - 只有是XT2来源MCLK。-Descr iption: Proper selection of an external HF XTAL for MCLK is shown by first polling the OSC fault until XTAL is stable- only then is MCLK sourced by XT2.
LPM3
- msp430F149,说明：此程序运行在LPM3 MSP430通常在4秒的时间间隔，脉冲P3.4。 WDT ISR用来唤醒系统。- Descr iption: This program operates MSP430 normally in LPM3, pulsing P3.4 at 4 second intervals. WDT ISR used to wake-up system.
software-FLL
- msp430F149,说明：设置DCO时钟（台达）*（4096）使用软件FLL。DCO时钟输出P5.5作为SMCLK。DCO时钟，这是选定的SMCLK通TIMER_A的积分：LFXT1/8（4096），直到SMCLK等于德尔塔。- Descr iption: Set DCO clock to (Delta)*(4096) using software FLL. DCO clock is output on P5.5 as SMCLK. DCO clock, which is the sel
ALIENTEK-MiniSTM32_example
- 用c编写的基于ALIENTEK MiniSTM32_example的例子，适用于嵌入式开发-C prepared based ALIENTEK MiniSTM32_example example, for embedded development
TimerA3
- msp430F149,TimerA3的简单应用。说明：拨动P3.4使用软件和TA_0 ISR。切换每50000 SMCLK周期。 SMCLK时钟源TACLK。-Descr iption: Toggle P3.4 using software and TA_0 ISR. Toggles every 50000 SMCLK cycles. SMCLK provides clock source for TACLK.
TimerA3(2)
- msp430F149,说明：拨动P3.4使用软件和TA_0 ISR。Timer_A的配置模式，定时器溢出时TAR计数到CCR0。在这个例子中，CCR0装有20000。-Descr iption: Toggle P3.4 using software and TA_0 ISR. Timer_A is configured for up mode, thus the timer overflows when TAR counts to CCR0. In this example, CCR0 is l
TimerB7
- msp430F149,说明：拨动P3.4使用软件和TB_0 ISR。切换每50000 SMCLK周期。 SMCLK时钟源TBCLK。-Descr iption: Toggle P3.4 using software and TB_0 ISR. Toggles every 50000 SMCLK cycles. SMCLK provides clock source for TBCLK.
TimerB7(2)
- msp430F149,说明：拨动P3.4使用软件和TB_0 ISR。的Timer_B配置模式，定时器溢出时TBR计数到CCR0。在这个例子中，CCR0装有20000。-Descr iption: Toggle P3.4 using software and TB_0 ISR. Timer_B is configured for up mode, thus the timer overflows when TBR counts to CCR0. In this example, CCR0 is l
ToggleIO
- msp40F149,说明：拨动P3.4，P3.4内进行异或运算得到软件loop.ACLK= N /，MCLK= SMCLK=默认DCO〜 800K-Descr iption: Toggle P3.4 by xor ing P3.4 inside of a software loop.ACLK= n/a, MCLK= SMCLK= default DCO ~800k
UART9600
- msp430F149,说明：回声一个接收到的字符，RX ISR使用。在主循环UART0准备接收一个字符中断活跃。主循环等待LPM3。UART0的ISR部队主循环后退出LPM3接收回波接收到的字符一个字符。-Descr iption: Echo a received character, RX ISR used. In the Mainloop UART0 is made ready to receive one character with interrupt active. The Mainl