资源列表
code
- ARM CORTEX-M3,代码，基于德州仪器LM3S系列芯片-ARM CORTEX-M3, code, based on Texas Instruments chips LM3S
LED
- 汇编语言，89c91单片机按键控制流水灯-Assembly language, 89c91 microcontroller control buttons light water
485bus
- RS-485采用平衡发送和差分接收，因此具有抑制共模干扰的能力。加上总线收发器具有高灵敏度，能检测低至200mV的电压，故传输信号能在千米以外得到恢复。-RS-485 uses balanced differential transmit and receive, so it has the ability to suppress common mode interference. Plus bus transceiver with high sensitivity, can detect vo
isis
- 单片机甲机乙机源代码。单片机甲机的P3.2外接按键K1，P3.3外接按键K2；单片机乙机P0、P2端口作为输出口，外接一个2位LED数码管。-A Machine B Machine SCM source code. A key K1 MCU P3.2 external machine, P3.3 external key K2 SCM B machine P0, P2 port as an output port, an external two LED digital tube.
shoufayiti
- 基于STC12C5A60S2的关于nrf24l01的无线通讯，接收和发送用同一函数，通过LED亮灭来辨别是否接收到数据和发送了数据。- Based on nrf24l01 STC12C5A60S2 wireless communications, the receive and transmit with the same function, through the LED light out to identify whether the received data and send
main
- msp430f1611单片机pid控制稳定电压输出的程序。误差5 左右。-msp430f1611 stable voltage output microcontroller pid control procedures. Error of about 5 .
1602
- 51单片机1602液晶显示程序，调试使用的是stc89c52单片机。-51 MCU 1602 LCD procedures, debugging using stc89c52 microcontroller.
midtest_pls
- 此代码适用P89V51（东南大学电子）利用实验板和串口助手设计程序：先从串口助手发送四个十六进制数据（0～F）到实验板，数码管DS1-DS4显示此数据。 并且拨码开关某位（自选）为ON时，接下来从串口发送的数据从左进入到显示序列，如原本数码管显示 ”0FE6”，在串口发送 ”A” 后变为为 ”A0FE”。 拨码为OFF时，发送 ”A” 会使显示变为 “FE6A”，也就是数据从右边进入显示。-This code applies P89V51 (Southeast University El
main_xiaoche
- msp430f149单片机编写的自动避障程序，读者可以参考修改。-msp430f149 MCU write automatic obstacle avoidance procedures, the reader can refer to the modifications.
main_yaokong
- 基于msp430f149单片机的遥控小车设计程序，小车使用遥控器为普通编码电视遥控器。-Msp430f149 microcontroller based remote control car design program, car using the remote control for the TV remote control common coding.
DS18B20OK
- 实现了18b20温度采集，并可以将采集到的睡通过串口发出-Achieved 18b20 temperature acquisition and sleep can be collected through the serial port issued
KeyLED
- zlg7289的灯板读取数值程序，给7289输入cmd返回数值-ZLG7289LED CODE