资源列表
wannianli
- DS1302+18B20万年历1602显示,加入了些自己的东西完美实现-DS1302+ 18B20 calendar 1602 show, adding the perfect realization of some of their stuff
ads1118
- 德州仪器生产的AD转换器ads1118的驱动程序，msp430作为主控。-Texas Instruments AD converter driver ads1118' s, msp430 as the master.
yejing
- 液晶1602静态显示,加入了些自己的东西完美实现-LCD 1602 static display, adding the perfect realization of some of their stuff
yejing2
- 液晶1602动态显示,并加入了自己的东西完美实现-1602 LCD dynamic display, and add their own thing to achieve perfection
TFT(SSD1289)
- 3.2寸TFT液晶驱动程序，液晶的驱动芯片是SSD1289.-3.2-inch TFT LCD driver, LCD driver chip SSD1289.
FFUControler
- 可控硅调节马达的转速的控制程序，可以直接使用。-SCR control procedure of adjusting the rotational speed of the motor, can be used directly
Modbus_Slave_example
- 采用STM32F103R8T6开发出的Modbus从站的一个例子，实现了正常通信，附带有原理图。-An example the station STM32F103R8T6 developed using Modbus, realizes the normal communication, containing schematics.
033T-CP
- ATT功能,PE4302串口控制，初始值为无衰减,RU监控板CDMA DL编码开关手动设置、OMT对应远端机CDMA DL ATT均可设置，与手动的衰減器设定值，以最后的操作方式为主，设定值在系统重启后仍然保持最后的设定值；-ATT function, PE4302 serial control, the initial value without attenuation, RU monitoring board CDMA DL coding switch manually set, OMT c
SIN_SPWM
- 利用SPWM调制产生正弦信号，可运用与各种电子器件的测量，如电压、电容、电阻等。-SPWM modulation using sinusoidal signal can be measured with the use of various electronic devices, such as voltage, capacitance, resistance and the like.
ADC0_Buf1
- 此程序为使用ADC0的例程 在中断模式使用定时器3溢出作为开始启动信号并采样AIN0<NUM_SAMPLES>次将结果存储在XDATA空间 一旦<NUM_SAMPLES>次被采集 采样值从UART0传输 一旦传输结束 另一个数据采样次数<NUM_SAMPLES>将被采集并重复此处理过程.-This procedure for routine use ADC0 interrupt mode using the timer 3 overflow started a
ADC0_Poll1
- 此例程说明了 ADC0在查询模式的操作 ADC0设置为写AD0BUSY作为其转换开始信号 并测量片内温度传感器的输出温度传感器的输出转换成摄氏度并从UART0传输。-This routine illustrates the ADC0 ADC0 set the query mode in operation for write AD0BUSY as its conversion start signal and measuring the on-chip temperature sensor
OSC_Cry1
- 此例程说明如何配置外部振荡器驱动22.1184Mhz晶体及如何选择此外部振荡器作为系统时钟 同时使能丢失时钟检测器复位功能。 假定22.1184Mhz晶体连接在XTAL1和XTAL2之间-This routine shows how to configure an external crystal oscillator drive 22.1184Mhz and how to this external oscillator as the system clock while Enable