资源列表
ITEMP
- stm32f103内部温度传感器测试程序，可作为驱动使用-The testing procedures of STM32F103 internal temperature sensor , can be used as a driver to use
CH378EVT.ZIP
- ch378读写U/USB盘芯片相关资料,里面有源程序和对应的一些文档资料-Usb chip ch378, speaking, reading and writing
GPRSwenshidapeng
- 四个从机检测温湿度和光照度，通过nrf24l01发送到主机，主机通过nrf24l01接收并在2.8寸tft上显示，最后主机通过gprs模块把收到的信息发送到电脑tcp服务器。-Four slave detect temperature, humidity and light intensity, sent via nrf24l01 to host, received and displayed on a 2.8-inch tft, finally host through gprs module
rfid-MENJIN
- 门禁系统设计，通过刷卡和按键输入检测密码是否正确。输入密码正确电机转动。输入密码错误蜂鸣器报警。-Access control system design, input detection password via credit card and keys are correct. Enter the password is correct motor rotation. Enter the password error buzzer alarm.
tiwenji
- 本文介绍了基于STC12C5A60S2单片机的测量功能系统，系统实现对温度的检测，同时具有万年历时钟显示功能。-This paper describes measurements based STC12C5A60S2 SCM system, the system realize the detection of temperature, but also has calendar clock display.
chaoshengboceju
- 本设计介绍了基于单片机控制的超声测距的原理：由STC89C52控制定时器产生一定频率脉冲，计算从发射到接收回波时间，从而得到实测距离，数据处理采用，lcd1602显示距离，WTD588D语音播报。-This design introduces MCU control based on the principle of ultrasonic distance measurement: STC89C52 controlled by a timer to generate a certain freq
MPC5604B_ADC
- MPC5604B的ADC模数转换代码，使能ADC0和ADC1的模数转换功能，扫描采集方式。-MPC5604B the ADC analog to digital conversion code to enable ADC0 and ADC1 analog to digital conversion, scan acquisition mode.
MPC5604B_PWM
- MPC5604B的FlexPWM信号输出代码，设置通道23作为21和22通道的周期时基21和22通道的周期为100us，占空比分别为80 和20 -The FlexPWM MPC5604B signal output code, the channel 23 is provided as a cycle 21 and cycle 22 the channel 21 and the channel base 22 is 100us, the duty cycle was 80 and 20
MPC5604B_I2C
- MPC5604P单片机通过I2C接口向AT24C02发送一个字节的数据并把数据读出，检测读出的数据是否正确，正确则点亮指示灯-MPC5604P microcontroller through the I2C interface to send a byte of data to the AT24C02 and the data is read out, the test data read is correct, correct, indicator lights
MPC5604B_PIT
- MPC5604B的PIT中断代码，使能PIT1中断，计时周期为0.5秒，每次中断改变D1灯的状态，D1灯每隔1秒闪一次-MPC5604B the PIT interrupt code, enabling PIT1 interrupt ticks for 0.5 seconds, every time you change the lamp status interrupt D1, D1 lights flash once every 1 second
MPC5604B_RTC
- MPC5604P的RTC中断代码，设置RTC中断的时间间隔约为0.5秒，D1每隔约1秒闪一次-MPC5604P the RTC interrupt code, set the RTC interrupt interval of approximately 0.5 seconds, D1 at intervals of about one second flash once
IAP_USB_Bootloader_V1.0
- IAP_USB_Bootloader尽量不要让站长把时间都花费在为您修正说明上-IAP USB Bootloader