资源列表
L298N-stepper-motor
- L298N是ST公司生产的一种高电压、大电流电机驱动芯片。该芯片采用15脚封装。主要特点是：工作电压高，最高工作电压可达24V；输出电流大，瞬间峰值电流可达3A，持续工作电流为2A；最大功率25W。-L298N is produced by ST a high-voltage, high current motor driver chip. The chip uses 15-pin package. The main features are: high voltage, the maximum
serial-communication
- 串口通信(Serial Communication)， 是指外设和计算机间，通过数据信号线 、地线、控制线等，按位进行传输数据的一种通讯方式。这种通信方式使用的数据线少，在远距离通信中可以节约通信成本，但其传输速度比并行传输低。-Serial Communication (Serial Communication), between peripherals and computer means, through the data signal lines, ground, control lin
infrared-receiver-principle
- 红外遥控器工作原理:红外线遥控就是利用波长为0.76~1.5μm之间的近红外线来传送控制信号的。-Infrared remote control works: infrared remote control signal is transmitted using near-infrared wavelength between 0.76 ~ 1.5μm.
Smart-car-framework-program
- 飞思卡尔智能车基本框架程序，XS128各模块程序，对于智能车电机，舵机，AD采集，放大模块等等采用易懂编程，且均有备注，有新手有较大启蒙作用。-Freescale basic framework of the smart car procedures, XS128 module procedures, for the intelligent car motor, steering gear, AD sampling, amplifying module and so on use simple
Dual-IR-emission-principle-obstacle
- 通过2路红外发射，顺序接收，检测收发功能是；用手遮挡对应的发射管，用共阳数码管的a、d端模拟；每60ms分别检测2路发射，通过每组发射10个脉；-By 2-way infrared emission, in the order received, the transceiver function is detected hand block corresponding to emission control, with a total of Yang digital tube a, d-end
swing-servo-sector
- 舵机的工作原理。舵机常用的控制信号是一个周期为20毫秒左右，宽度为1毫秒到2毫秒的脉冲信号。当舵机收到该信号后，会马上激发出一个与之相同的，宽度为1.5毫秒的负向标准的中位脉冲。-Steering works. Servo common control signal is a period of about 20 milliseconds, a width of the pulse signal 1 ms to 2 ms. After receiving the servo signal, it
Ultrasound-in-the-serial-port
- 用XS128对超声波进行采集测距，精度可达到1 cm，同时采用XS128的SCI功能，可与电脑进行串口通信，电脑发送AA,即返回测距值到电脑-With XS128 for acquisition of ultrasonic ranging, precision can reach 1 cm, adopting XS128 SCI functions at the same time, can communicate with computer by serial port, the comput
iLI9486
- ILI9486显示屏幕的驱动程序，C语言描述-ILI9486 frequency display driver
chaoshengbo
- 超声波测距模块的驱动程序，LCD1602显示-Ultrasonic ranging module drivers, LCD1602 display
Ele_Measure
- 简易频率计设计程序，可用于单片机开发，Keil工程-Simple frequency meter program
Unmanned
- 基于对加密无人机飞控而叠加的利用XS128单片机进行检测飞控发出信号判断方向，再利用超声波检测距离前方距离，若小于设定距离，判断前进方向又是向前，则切断飞控信号，切换成固定PWM，使飞机悬停，若检测是向后方向，则切换为飞控信号。-Encryption based on the use of uav flight control and overlay XS128 single-chip microcomputer testing flight control signal to determin
5110
- 基于XS128单片机的5110驱动程序，包含字库，符号，线性图像等等。-XS128 based on single chip microcomputer 5110 drivers, including character, symbol, and the linear image and so on.