资源列表
pashangfa
- 基于C语言的爬山法，可以改变步长，使系统快速精确找到最大功率，很好！-Climbing method based on C language, can change the step length, the system quickly and accurately find the maximum power, very good!
huangjingfengefa
- 基于C语言的黄金分割法法，可以改变步长，使系统快速精确找到最大功率，很好！-Method of golden section method based on C language, can change the step length, the system quickly and accurately find the maximum power, very good!
eight
- 八位数码管显示数字，学号，可以滚动显示要显示的英文数字等-Eight digital tube display digital, student number, can scroll the display to display digital English etc.
cms015
- 液晶CMS015，主控HX8309A，包含datasheet和示例代码- LCD CMS015, master HX8309A, comprising datasheet and sample code
DIY-51-Programmer
- 自己动手做51系列单片机编程器,提供了编程器原理制作思路-DIY 51 Series Microcontroller Programmer
TCD1206-P-TLC1549
- TCD1206 实现光源的采集，通过1549转换后传给单片机，单片机将数据通过串口传出- TCD1206 realize the collection source, through the 1549 conversion pass microcontroller, the microcontroller outgoing data through the serial port
MDK-bin
- 在 Realview MDK 的集成开发环境中，默认情况下可以生成*.axf 格式的调试文件和*.hex 格式的可执行文 件。虽然这两个格式的文件非常有利于 ULINK2仿真器的下载和调试， 但是 ADS 的用户更习惯于使用*.bin 格式的文件， 甚至有些嵌入式软件开发者已经拥有了*.bin 格式文件的调试或烧写工具。- In Realview MDK integrated development environment, by default, you can generate
TELCAL
- 1.送電時，EOM的指示燈亮,S1將切至錄音位置,按住REC按鈕,EOM指示燈熄,開始錄音第一段,如 本人不在,逼聲後,請留言 -1. power transmission, EOM indicator light, S1 will switch to the recording position, and hold the REC button, EOM indicator turns to start recording first paragraph, such as I am no
TELARM
- 1.送電時,顯示12:00:00的時間且開始計時,同時8051也進入M6操作按鈕模式,隨時可做錄音 2.P3.0按鈕控制, 時分秒顯示 閃爍位置的調整,按住P3.0超過3秒鐘後, 時 閃爍 -1. transmission, display 12:00:00 time and start time, while 8051 also entered the M6 operation button mode, recording time available 2.P3.0 button
RECORD-CAL
- Winbond的ISD2500系列提供高品質,單片機,解決聲音錄放問題.此CMOS IC包含有晶片上的震盪器,MIC放大器,自動增益控制,防止聲音失真濾波器及喇叭放大器.-Winbond s ISD2500 series provides high-quality, single-chip, to solve the problem of sound recording. This CMOS IC contains the oscillator on the wafer, MIC amplifi
AUTOTEL
- 1.利用UM95089送出複頻訊號,經由ST-71耦合至電話線傳送出去,UM95089詳細資料. 2.設定3組電話號碼存入93C46,當有狀況時,由UM95089自動撥號出3組電話號碼.-1. Using UM95089 send complex frequency signals coupled via ST-71 to the telephone line to send out, UM95089 details. 2. Set 3 phone numbers stored in
TEL-REMOTE
- 1.電話筒掛著時,其兩端電壓約為DC48~50V. 2.震鈴信號為正旋波VP-P=100V,20HZ 3.電話筒拿起時,其兩端電壓為DC5V-1. telephone handsets hanging, the voltage across about DC48 ~ 50V. 2. ringing signal is sine wave VP-P = 100V, 20HZ 3. Pick up the telephone receiver, the voltage for DC5