资源列表
chengxu
- MEGA48控制LCD1602显示内部字符，例程，可供参考-MEGA48 control LCD1602 display the internal character, routines, available for reference
m48-E2D6FE.jpg
- MEGA48内部8M晶振设置参数，供参考-MEGA48 within 8 m crystals set parameters, for your reference
3ch-16bit-pwm
- 这个是STC的16位pwm源码，普通8位单片机只能做到8位，而这个有16位的精度。-This is a 16-bit PWM source on STC, ordinary 8-bit microcontroller can only do 8 bits, and the accuracy of the 16.
cPP
- solve differential equation
danpianji
- 将8031内部RAM，40H～4FH单元分别置初值A0H～AFH，然后将40H～4FH单元内容分别传送到片外RAM的0800H～080FH单元，再将片外0800H～080FH单元内容传送到片内60H～6FH单元。-8031 internal RAM, 40 h ~ 4 fh unit set initial value A0H ~ AFH respectively, then the content of the 40 h ~ 4 fh unit respectively transmitted
danpianji2
- 三字节加法。被加数置于30H~32H单元 加数置于33H~35H单元 结果置于40H~42H单元 -8031 internal RAM, 40 h ~ 4 fh unit set initial value A0H ~ AFH respectively, then the content of the 40 h ~ 4 fh unit respectively transmitted to the outside of the piece of RAM 0800 h ~
danpianji2
- 掌握如何使用803l的外部中断方法。掌握中断的程序设计方法。中断响应时，P1．4～P1．7显示P1.0~P1.3的开关状态，要求外部中断采用边沿触发式。 实验原理图与建议接线图如下图所示： -To grasp the method of how to use the 803 l external interrupt.Mastering the interrupt program design method.Interrupt response, P1.4 ~ P1.7 shows P1
51
- 51单片机源程序 DS1302S时钟显示 RF905无线模块代码 -51 microcontroller source DS1302S clock display RF905 wireless module code
menling
- 当按下QX-MCS51上的S2键后，蜂鸣器会发出十次短暂的“嘟嘟”声作为呼叫。 S3用于关闭或者打开门铃。 当门铃处于关闭时，按下S2不会有呼叫效果。-When you press the S2 key on the QX-MCS51, beeper ten times short " beep" as a call. S3 is used to close or open the door. When the door is closed, press S2
loutizaoming
- 实现楼道间照明灯的方便控制，一个照明灯，在楼上和楼下各有一个（闭合式）开关控制。-Achieve inter-corridor lighting control convenience, a lamp, upstairs and downstairs each have a (closed) switch.
canpinshuliangjishuqi
- 其中S2用于模拟代替扫描开关，当有产品经过时，会使S2送出低电平（本程序中是用手按下S2来模拟） S2每按一下，便会使数码管上的计数器加一。-Wherein S2 is used in place of the analog scanner, when the product passes, S2 will send a low level (this program is to simulate hand pressing S2) S2 each click, it will make
24l01ceshi
- 液晶1脚接1602黑色排母的1脚 如果是无背光的液晶只有14个脚 排母右边空2个位 请把液晶对比度电位器顺时针调制10点钟方向，请勿多调超出极限位置会损坏电位器！-1602 black crystal pin 1 to 1 foot row home if it is not backlit LCD only 14 feet right of the row home empty two bits Please LCD contrast potentiometer clockwise m