资源列表
12864Pds1302
- 使用MSP430F149编写的DS1302程序，并使用LCD12864显示-Use the MSP430F149 preparation of the DS1302 program, and use LCD12864 display
ICCAVR_mega8sfdg
- AVR单片机 atmega8单片机 串口发送接收 proteus仿真和ICC程序 -AVR microcontroller the atmega8 microcontroller serial port send and receive proteus simulation and the ICC program
ICCAVR_mega8dgkfdhk
- AVR单片机 atmega8单片机 两位数码管显示 proteus仿真和ICC程序 -Atmega8 microcontroller AVR microcontroller two digital display proteus simulation and the ICC program
ICCAVR_mega8lglhk
- AVR单片机 atmega8单片机 外部中断运用 proteus仿真和ICC程序 -AVR microcontroller atmega8 external interrupt using proteus simulation and the ICC program
LED_track
- 基于msp430F5438的点光源跟踪系统程序，2010年江苏电设题目，学校培训时做的一个练习，是当时所有队中效果最好的一个，执行机构用的是舵机-Point source tracking system based on msp430F5438 the program in 2010, Jiangsu power set topic, school training to do an exercise, when all the team one of the best executive bo
Driver7SegmentLEDby74hc595
- 8051 控制 74hc595 来驱动 七段显示器, 以显示 0-9 数字-8051 control 74hc595 to drive seven-segment display to show the 0-9
uart_rs232
- 基于MSP430F5438A的RS232串口通讯程序-RS232 serial communication program based on MSP430F5438A
4channel_AD_Multi_convertion
- 基于msp430F5438A的4通道8次AD转换程序，可参考调用-Based on the 4-channel 8 msp430F5438A AD conversion process, refer to the call
AD-value-print
- 基于msp430F5438A 的AD值打印到串口，方便程序调试-The AD value based on msp430F5438A print to the serial port, to facilitate debugging
CH452--drivers
- 包含了CH452的驱动例程，已经调试通过。里面有两个例程，一个是51的(keil)，一个是430G2452的(CCS)-Contains the CH452 driver routines have been through debugging. There are two routines, one is 51 (the keil), one the 430G2452 of (CCS)
DS18B20
- 开发环境：EWARM mcu:STM32 温度传感器DS18B20的温度实时显示（开机画面） 硬件环境： TFT:PE0-PE15--->DB0-DB15 PD7->CS PD8->RS PD9->WR PD10->RD PD11->RESET DS18B20：DQ-->PD4 功能： 显示开机画面，且环境温度的实时显示-Temperature sensor DS18B20 temperature real-time disp
nRF2401A-transportation
- TX为发送程序不断发送TxBuf里的数据，RX为接收程序当接收到数据之后就把当前数据从串口发出。波特率 无奇偶校检，9600，N，1。 程序已编译通过，可直接下载.hex文件到模块上即可实现程序功能。-TX data is send the program continue to send TxBuf the RX when the received data to receive the program put the current data sent from serial por