资源列表
128642BDS13022B18B20
- 温度传感器ds18b20 时钟ds1302和 12864lcd 的程序 简单明了 很好理解的程序-Clock ds1302 temperature sensor and 12864lcd ds18b20 process well understood by simple procedures
J_LINK_v7_sheme
- shematic prints if J_Link version 7. JTAG for IAR developing system.
ConstantpowerDMX
- 三通道DMX512解码控制芯片,全彩大功率LED控制芯片应用资料-Control of three-channel DMX512 decoder chip, full-color high-power LED control chip application data
Motorola_Mask
- software for motorola microcontroller
avr_16x2_lcd_driver
- AVR LCD 16x2 driver showing how to read/write to an LCD through an AVR chip. The lcd uses either an 8 pin or 4 pin interface.
cordic
- 此段程序为CORDIC的实现，参照论文加速CORDIC算法的实现-CORDIC implementation procedures for this section, reference to paper to accelerate the realization of CORDIC Algorithm
F340_ad
- 例程说明，本程序是c8051f340对电位器产生的电压值进行采样,可以在寄存器观察AD的 也可以通过LCD将值显示出来,由于LV595芯片片选引脚与以太网控制芯片CP2200 中断引脚复用因些在此例程中加入了将CP2200芯片中断关闭的代码。件-Routine descr iption of the potential of this program is c8051f340 voltage generated by sampling can be observed in the AD
LCDWNL
- *日历时钟 * *按K1,进入设置状态 * *按k2,停止闹钟声音 * *按k3,依次进入闹钟功能是否启用，闹钟时,分秒,年,月,日及时间时,分,秒的设置, * *直到退出设置状态 * *按k4,调整是否起用闹钟和调节闹钟时,分,秒,年,月,日,时间的时,分,秒的数字 * *LCD第二排中间显示小喇叭，表示启用闹钟功能，无则禁止闹钟功能 * *（可在调整状态进行设置） * *正常状态,LCD上排最前面显示自定义字符,LCD下排最前面闪动"XUELIN" * *
FESTOpneumaticsystemcleaningfilterMIDIseries
- 清洁FESTO气动系统MIDI系列过滤器FESTO pneumatic system cleaning filter MIDI series-FESTO pneumatic system cleaning filter MIDI series
8051_Proteus
- 1.所有案例硬件仿真时需要Proteus7.1或以上版本. 2.C程序开发集成环境Keil uVision要求3.0或以上版本. 所有案例C源代码由配套书籍提供,压缩包中不提供C源代码, 仅提供由C程序编译生成的HEX文件. 3.如果有相关技术资料在压缩包中未找到, 读者可从www.icpdf.com免费下载. (下载之前需要先注册) 相关案例需要的软件:超级编辑器UltraEdit, 虚拟串口驱动vspd,串口助手, 字模软件
Tetris
- 绝对可用的单片机上运行的俄罗斯方块源代码，LCD为RA8835。-Tetris source code absolutely can run on SCM. LCD driver is RA8835
Cargador
- 绝对可用的单片机上运行的推箱子源代码，LCD为RA8835。-Cargador source code absolutely can run on SCM. LCD driver is RA8835