资源列表
LCD_2
- 128*64液晶显示汇编程序，已经经过测试，可以直接使用-128 * 64 LCD assembler, has been tested and can be used directly
timerPIC_17C756
- PIC单片机的定时器使用的demo程序.内附说明.
HT48_xxMCU_HT1621write_read_C
- HT1621 是一款128 个位元的LCD 控制器件，内部RAM 直接对应LCD 的显示单元。相应的软件使它适用于包括LCD 模块和显示子系统在内的多功能应用。主控制器与HT1621接口只需4 到5 根线。内置的省电模式极大的降低了功耗。本文介绍HT48R05A-1 单片机来控制HT1621，并介绍如何turn ON 及turn OFF LCD 所有位元。-HT1621 is a 128-bit LCD control device, the internal RAM directly corr
display7
- 单片机时时通信程序 向欻耨发一组8位数据 可在P1口电量相应的灯-Single-chip communication procedures from time to time made to the Nou suddenly a group of 8-bit data can be in the P1 corresponding light power I
paomadeng
- 使用51单片机编写的跑马灯程序，顺序点亮8个发光二极管，并闪烁-Marquee prepared using 51 single-chip program, the order of 8 LED lights, and flashing
electronic-clock
- 这是一个简单的51单片机编写的程序，可实现时间的准确显示-This is a simple program written in the 51 SCM can achieve an accurate display of time
bujingC
- 简单设计步进电机的驱动C程序！方便调试和再添加学习！-Simple design stepper motor drive C program! Easy to debug and add learning!
Timer-control-traffic-lights
- 东西向绿灯亮 5s 后，黄灯闪烁，闪烁5 次亮红灯， 红灯亮后，南北向由红灯变成绿灯，5s 后南北向黄灯闪烁， 闪烁5 次后亮红灯，东西向绿灯亮，如此往复-East-west green light 5s after the flashing yellow light flashes 5 times red. Red light, north and south from the red to green, 5s after the north and south to the fl
MCU-button-interface-program
- 这是一个51单片机按键接口的源程序，是用C程序写的，是我自己写的，可以在51单片机上成功运行。-This is a source of the 51 microcontroller keys interface is written in C program, I wrote it myself, you can run successfully on 51 SCM.
2
- 程序功能为基于10位的高精度DAC数模转换器，实现频率比较高的周期周期性信号输出，分别实现锯齿波和三角波输出，通过控制插入的软件延时可以达到调节输出信号频率的目的。-Program function is based on 10-bit precision DAC digital-to-analog converter, to achieve a relatively high frequency periodic periodic signal output, respectively, to
display
- ds1302做的时钟，开机动画程序，显示用共阳6位8段数码管-ds1302 clock to do, boot animation program
ad9984
- 做项目用单片机配置的ad9984代码，此部分是用芯片的VGA输入端，将VGA信号转换为24bitRGB给后级使用，因为涉及项目只贴出ad9984配置部分。- Do projects MCU configuration ad9984 code, this part is the VGA input of the chip, the VGA signal into 24bitRGB to use after the class, because it involves only poste