资源列表
MCU_TA_UART_send_recrive
- 我本人写的430单片机无线发和接受的程序，在板子上测试过，没有问题，希望对大家有帮助啊，好东西大家一起分享。-I am writing wireless MCU development and acceptance of 430 procedures, the board tested, no problem, we want to help ah, good things to share with everyone.
programe
- 基于单片机控制的电子秤，（包括12864液晶屏的显示，模数转换程序ad7705，SPI协议，i2c协议，外存储空间的扩展等）-Microcomputer-controlled electronic scales, (including 12 864 LCD display, analog-digital conversion process ad7705, SPI protocol, i2c protocol, external memory expansion, etc.)
jichu
- 51单片机C语言程序基础教程。如需配套开发板，请加QQ：394011495。并注明。-51 Single-chip C Programming Language Essentials. For supporting development board, please add QQ: 394011495. And annotated.
lamp
- protues与keil实现，流水灯及各种花样，16位矩阵键盘控制，51单片机，源程序完整，自己编写的-protues and keil achieve, water lights and all kinds of tricks, 16 matrix keyboard control, 51, complete source code, I have written
pinghengche_8051
- stc15W4k61s4平衡小车源码，使用TB6612点击驱动，包含互补滤波，低通滤波，8051代码模式，简单易懂，并含有PS2手柄解码程序-Stc15W4k61s4 balance cart source code, using TB6612 click the drive, contains the complementary filter, low-pass filtering, 8051 code mode, easy to understand, and contain the PS2
delest3mic
- 2D Acoustic source location. This simulates an acoustic source traveling in a semi-circle around 3 microphones. You can see the semi-circle and the estimate. You can change various parameters.
51procedure123
- 51单片机一些C语言程序包，包含按键处理，12864液晶显示，无线遥控，步进电机等几十个模块的程序，有用的朋友下过去参考下吧！-51 microcontroller some C language package includes keys, 12,864 LCD, wireless remote control, Stepper motor scores module procedures useful friends under the past under reference!
ASETOFPROGRAMFORC51
- 一些单片机C程序，希望对初学者有一定作用
c8051f020-dac-generate-sin-wave
- 采用C8051F020 DAC产生任意波形-c8051f020 dac generate sin wave
时钟成品12864fei
- 利用ds1302，显示年月日时分秒，按键调节时间数据，显示在128864液晶显示屏上。(The use of DS1302, display the date when, button adjustment time data displayed on the LCD screen in 128864.)
sn8p2711a
- SONIX的单片机SN8P2711AS/BS交流电机控制可控硅方案源码(SONIX microcontroller SN8P2711AS/BS AC motor control SCR program source code)
AT8PE513M_LED
- AT8PE513M控制RGB调光程序 1. 未按开关SLEEP,长按2秒开机、再长按2秒关机 2. 开机后，红，绿，蓝滚动渐变发光 3. 每按一下，功能依次: 红灯恒亮，绿灯恒亮，蓝灯恒亮，红灯闪亮，绿灯闪亮，蓝灯闪亮，重回2步滚动发光(At8pe513m control RGB dimming program 1. If the sleep switch is not pressed, press and hold for 2 seconds to start up, and then pre