资源列表
DACONTROL
- 基于CY7C68013上的固件开发AD转换源码，附原理图一张-CY7C68013 firmware development based on the AD converter source code, with a schematic diagram a
LCMCONTROL
- 编程环境keil，基于CY7C68013上的USB开发，USB固件源码+原理图-Programming environment, keil, based on the CY7C68013' s USB development, USB firmware source code+ schematic diagram
StepMotor.c
- 单片机控制步进电机的正反转，转速调节等功能。-Positive inversion stepper motor microcontroller control, speed adjustment and other functions.
F340_i2c(readandwrite)
- 做项目时编写的c8051f340中的iic模块的程序，该程序的功能是通过c8051利用iic模块来收发数据.-C8051f340 prepared to do projects in the iic module program, the program' s functionality through the c8051 using iic module to send and receive data.
pic_i2c(readandwrite)
- pic单片机的iic功能模块的读写程序，是用c语言的读写实例，已通过编译调试.-pic microcontroller iic function module to read and write procedure is to use c language, reading and writing instance, has passed the compiled debugging.
danpianjitiaopingfangzhen
- 通过protues建立工程，对AT89C51单片机控制的16×80LED点阵条屏进行仿真运行，文件中包含完整的C语言源程序及目标程序。-Through the establishment of protues projects, AT89C51 microcontroller-controlled 16 × 80LED dot-matrix screen of the simulation run, the file contains the complete C language source
Releji
- relays 1-1 how to guide
ds18b20
- 详细说明：学习掌握单总线数字式温度传感器 DS18B20的64位激光ROM码的读出方法。读DS18B20 64位ROM码命令（33h）允许主机直接读出从机的64位ROM代码，而无须执行搜索ROM 过程。如果该命令用于多节点系统，则必然发生数据冲突，因为每个从机设备都会响应该命令。64 位激光ROM 从高位到低位依次由8 位CRC、48 位列号和8 位家族代码(28H)组成。--learning and mastering digital single bus DS18B20 64 laser
IDT7007RAM
- IDT7007高速双端口RAM及其应用 包括详细的功能原理说明-IDT7007 High-speed dual-port RAM and its application include a detailed descr iption of the Function Principle
AD590_Thermometer_Papers_and_code
- AD590作为温度传感，再通过模数转换把模拟信号转成数字信号，送入单片机进行处理并显示-AD590 as a temperature sensor, and then through the analog-digital conversion to analog signals into digital signals, into the microcontroller for processing and display
NOKIA3310
- NOKIA3310显示控制程序。使用MSP430单片机控制NOKIA3310的显示屏，超低功耗，非常好用。NOKIA3310显示屏在修手机的地方都能买到-NOKIA3310 display control procedures. Using the MSP430 MCU control NOKIA3310 display, ultra-low power consumption, very easy to use. NOKIA3310 display at the repair place to
printer
- 使用MSP430单片机，控制并口打印机。很好用，注意对应IO必须接在打印机相应的输入输出口上-The use of MSP430 MCU to control the parallel port printer. Useful, attention must be connected to the printer corresponding to IO input and output port on the corresponding