资源列表
stm32f10x_fw_archive
- ST Microelectronics STM32 Firmware Archive
华中科技大学飞思卡尔比赛CCD程序代码
- 华中科技大学飞思卡尔比赛CCD程序代码，摄像头数据处理与滤波-Huazhong University of Science and Technology the Freescale competition CCD code, camera data processing and filtering
在IAR环境下STM32F103ZET6驱动7寸液晶屏
- 在IAR环境下STM32F103ZET6驱动7寸液晶屏，分辨率为800*480 驱动芯片为RA8875，带触摸屏接口-In the IAR environment STM32F103ZET6 drive 7-inch LCD screen with a resolution of 800* 480 Driver IC for RA8875, with a touch screen interface
单片机控制的AD对正弦波信号采样后用12864的液晶显示出来
- 单片机控制的AD对正弦波信号采样后用12864的液晶显示出来,Single-chip microcomputer controlled sine wave signal AD to 12864 after sampling the liquid crystal display out
51单片连tcs230的源程序
- 51单片连tcs230的源程序，绝对原创，可以记忆颜色。 #define uchar unsigned char #include <reg52.h> #include<math.h> sbit S0=P1^7 sbit S1=P1^0 //端口定义 sbit S2=P1^1 sbit S3=P1^2 sbit OE=P1^3 sbit OUT=P3^4 //频率从TO口输入 sbit key0=P1^5 sbit LED=P1^6 s
PowerPCB/PADS封装库
- PowerPCB/PADS封装库，原版安装后没有的，有常见的SO、SOIC、TSSOP等格式，省去自己画封装的麻烦,PowerPCB/PADS package library, after the original installation, and have common SO, SOIC, TSSOP and other formats, saved themselves the trouble of packaging draw
用AT89S52单片机模拟警报声
- 用AT89S52单片机模拟警报声，消防车，救护车，婴儿啼哭及机枪声,Single-chip simulation using AT89S52 sirens, fire engines, ambulances, crying babies and machine guns
瑞萨单片机串口通讯的完整例程
- 瑞萨单片机串口通讯的完整例程，初次用此单片可以参考一下。 High-performance Embedded Worshop开发环境，R8C族,E8A仿真开发板,Renesas complete single-chip serial communication routines, the first time can use this single-chip reference. High-performance Embedded Worshop development environment
STC89C52RC单片机的手册
- STC89C52RC单片机的手册，中文。全面，便于开发查询。,SCM STC89C52RC manual, Chinese. Comprehensive, easy development of queries.
Microchip ZigBee协议栈源码
- Microchip ZigBee协议栈源码,内有使用示例和说明,Microchip Stack for the ZigBee™ Protocol V1.0-3.5 April 6, 2006 Version 1.0-3.5 is a newly architected release of the Microchip Stack for the ZigBee Protocol. It provides all the required features of the v
移植uip-1.0到Atmega32
- 移植uip-1.0到Atmega32 1）把 uip-1.0 的所有文件加入到工程，包括 uip 目录的文件（除uip-split.c）、unix 目录的文件、lib 目录的文件； 2）修改 uip/uip-neighbor.c 文件的 void uip_neighbor_add(uip_ipaddr_t ipaddr, struct uip_neighbor_addr *addr) 函数，一般注释掉 printf 语句即可，或者改为你自己的串口格式化打印实现。 3）u
并口扩4串口的程序，用的是16c554
- 并口扩4串口的程序，用的是16c554，和大家一起分享,4 serial parallel expansion of the program, use the 16c554, and the community together to share