资源列表
uCOSII_for_lpc1700
- 周立功1700系列芯片(CORTEX-M3内核)UCOS-II操作系统的KEIL开发环境的工程模板，有需要的就下载吧-Zhou, who KEIL project templates for the 1700 series chips UCOS-II operating system, there is a need to download
MusicShow
- 8952 单片机接收矩阵键盘输入并且确定按键值，不同按键对应不同定时时间长度。通过时间长度不同播放不同音乐。proteus仿真通过-8952 MCU receives the matrix keyboard input and to determine the key values, different buttons corresponding to the different timing the length of time. The length of time to play diff
7segshow-drive-by-8952
- 单片机实现七段数码管显示采用89C52单片机控制 74LS273作为断码及扫描输出地址锁存。proteus仿真调试通过-MCU segment digital display 89C52 microcontroller control 74LS273 latch broken code and scanning the output address. proteus simulation debugging through
NRF_RX
- 采用STC12C5A60S2实现NRF24L01的接收测试代码，内含5个.c和.h文件，在Keil uv3环境下编译-The receiving test code of the NRF24L01 STC12C5A60S2 containing 5. C. H file in the compiled under Keil uv3 environment.
NRF_TX
- 采用STC12C5A60S2实现NRF24L01的发送测试代码，内含5个.c和.h文件，在Keil uv3环境下编译-The STC12C5A60S2 achieve The NRF24L01 send a test code containing 5. C. H file in the compiled under Keil uv3 environment.
tlc2578
- PIC16f877A单片机控制TLC2578的AD转换程序，调试通过！-PIC16f877A SCM TLC2578 the AD conversion process
interruput
- 内容：通过中断接口P3.2连接的独立按键测试，按一次P1口的LED灯反向， 这里使用边沿触发，所以一直按键不松开和一次按键效果相同，区 别于电平触发-: Interrupt the interface P3.2 connection, independent of the key test, a P1 port LED lights reverse, edge-triggered, it has been the key to not let go, and a button ha
time1
- 内容：通过定时让LED灯闪烁,这里使用定时器最大值从0开始计数一直到65535溢出-: Timing LED lights flashing, timer maximum value to start counting from 0 to the 65535 overflow
io
- 内容：点亮P1口的一个LED灯 该程序是单片机学习中最简单最基础的， 通过程序了解如何控制端口的高低电平-Content: an LED light P1 port of the program is the simplest and most basic single-chip learning through the process to understand how to control port high and low
99miao-ji-shi
- 内容：通过定时器实现大于定时器单次最大计时时间的计时，计时时间能够达到99秒-Than the timing of the single largest timer timing time: timer
46-bu-jin-dian-ji-zhen-fan-zhuan
- 内容：1、本程序用于测试4相步进电机常规驱动 2、需要用跳帽或者杜邦线把信号输出端和对应的步进电机信号输入端连接起来 3、速度不可以调节的过快，不然就没有力矩转动了 4、按s4（设置成独立按键模式）可以控制正反转 -Content: This program is used to test the four-phase stepper motor conventional drive 2, you need to jump the caps or the DuPont l
50-hong-wai-jie-ma
- 内容：按配套遥控器上1-9会在数码管上对应显示-: 1-9 on supporting the remote control corresponding digital tube display