资源列表
dsPIC33FJ256GP710A
- dsPIC33 UCOS sPIC33 microchip dsPIC UART
NUC950_uCosII
- nuc950处理器的ucos移植,已移植好,针对nuc950开发板。-The nuc950 processor uCOS transplantation Transplantation, has been good, according to the nuc950 development board.
STM32PUCOS-II=GPIO_PS2_TIM
- 1.板上的8 个按键分别 代表数字1-8,按下一个按键将结果通过串口发送到PC机上显示; 2.使用两个定时器模块,分别定时为1ms 和100ms 产生中断,使用它们分别 产生1s的定时时间,将时间分别显示到数码管上; 3.外接PS/2小键盘,将按键的值通过串口显示到PC机上。-A panel of eight key representing the number 1-8 press a key the results sent through the serial port on
stm32-gprs
- 基于STM32、UCOS的GPRS驱动程序,支持TCP/IP传输,DNS查询,短信-STM32, UCOS GPRS driver supports TCP/IP transport, DNS queries, text messaging
Ethernet
- 网口芯片KSZ8041的源代码,配合NXP的LPC1788,采用UCS操作系统,调试通过,放心使用-The chip the KSZ8041 the source code of the network port, with the NXP LPC1788 UCS operating system debugging through, ease of use
STM32F103_uCOS_emWin5.18
- 用stm32f103系列ARM芯片+Emwin +ucos-With stm32f103 series ARM chip+Emwin+ucos
uCOS-III-P-LwIP-On-VC
- ucosii在vc上的实验例程,可以直接使用,也可以在此基础上修改,完成自己的实验。-ucosii in vc experimental routines can be used directly, or you can modify on this basis, to complete their experiments.
uTenux
- µ Tenux嵌入式实时操作系统是基于日本T-Kernel开发而来,从2009年发布升级至今。上传版本为V1.6版本。 1、现在已经支持IAR、Keil、eclipse+gcc三个环境。 2、主要支持ARM7/9、全线支持Cortex-M0、3、4的ARM内核芯片 3、支持CMSIS 4、只要应用医疗电子、工业控制、办公电子等 5、uTenux学习讨论群:218329305(CSDN推荐)-μTenux embedde
TinyOS(stm32)
- 这是uCOS-II 精简版在STM32 上的移植,体积很小,适合ROM很小的单片机,甚至是8位机,实战可用,实用价值很高,一般人我不给。-This is uCOS-II Lite on the STM32 transplantation, small size, suitable for a small ROM chip, or even eight machines, combat available, highly practical, and most people I do not gi
STM32F3-UCOS-II
- UCOSII 在STM32F303上移植,本人源码,使用或转载请说明出处-UCOSII the STM32F303 transplant, I source, use or reproduced, please indicate the source. . Thank you
9s12g48
- 飞思卡尔mc9s12g48/g64/g128 ucos-ii2.91代码移植实例 OS_CPU.H配置简单 OS_CPU_A.ASM尽量简化将两个关键函数放在OS_CPU_C.C中实现-Freescale mc9s12g48/g64/g128 ucos-ii2.91 code examples OS_CPU.H transplant simple OS_CPU_A.ASM try to simplify the configuration of the two key functions
SNTP
- 电能表SNTP对时的源码,通过lwip发送ntp的报文给服务器,收到数据后计算时间,与本机时间相差不超过五分钟,即修改本系统的时间。MCU采用的是LPC1768。-sntp lwip lpc1768