资源列表
little-car-send
- 小车采用STC12C5A16S2（主单片机）可以实现测量前方障碍物的距离，并实时发送给从单片机STC89C52，之后从单片机通过串口发送给电脑，此文件为发射端程序 -Car used STC12C5A16S2 (main MCU) can measure the distance between the front of the obstacle, and real-time to the slave microcontroller STC89C52, then sent from the mi
FreeRTOS_MSP430_IAR_zxWB_1a_v411
- FreeRTOS，TI430，做项目时由它改的，需要RAM 2K以上-FreeRTOS，TI430 a project by the change it, you need more RAM 2K
VC60_com
- 本程序使用VC6.0的通用串口控件MSCOMM32.OCX来对发送到串口的数据进行采集处理。主要使用方法 串口设置：m_Comm.SetSettings(“波特率，校验方式，数据位数，停止位数”) -This procedure using VC6.0 Universal Serial control MSCOMM32.OCX to sent to the serial data acquisition and processing. Mainly use the serial port
NTC_Temp
- 一个将NTC热敏电阻转化为 AD>>温度 对应数组的程序，并以图形方式体现出来，可以用来确定上拉电阻和下拉电阻合适否。回车键退出，参数输入方式见main开头办法。（上拉电阻和下拉电阻均有 不同的基准电压均有考虑 ）-An NTC thermistor will be converted to AD > > temperature corresponding array of procedures, and graphically reflected pull-up resi
Led8_Chg
- 一个将LED 8段码自动算出来的程序，定义好ABCDEFGH对应Di的位即可,输出ASM C等格式,个人用了十几年了分享下,TurboC2.0环境-A code segment LED 8 will automatically figure out the procedure, defined by bits Di ABCDEFGH corresponding output ASM C and other formats, personal to share with the next ten
Ccriterion-V0.2-20030401
- 一个将C程序自动规范化的程序，在编程时基本上格式化不用特别严格，在编完后运行一下，程序就规范了方便阅读，个人用了十几年了分享下,TurboC2.0环境-A C program will automatically standardized procedures, the programming format is basically not particularly strict, after running about in the series, the program is standar
STM32F4Discovery-VD-USB
- stm32f407discovery 开发板实现usb与电脑的通信 包括了上位机的测试软件 -stm32f407discovery usb development board to achieve communication with the computer, including a test of PC software
040spi
- C8051F040单片机SPI源程序，包括发送和接收部分，其中还包括舵机控制部分。-C8051F040 microcontroller SPI source, including sending and receiving section, which also includes servo control section.
33904_5
- 带CAN和LIN的系统基础芯片33904、33905说明-With CAN and LIN system basis chip 33904,33905 Descr iption
proj
- C8051 project for reading some Temp sensors using I2C and control fan using PWM
stm32_i2c
- 使用STM32F103系列的ARM-CORTEX-M3内核的CPU进行I2C总线读取。涉及到STM32控制，及I2C总线控制。-Use STM32F103 series of ARM-CORTEX-M3 core CPU for I2C bus to read. Involves STM32 control, and I2C bus control.
main
- 单片机平台上的12864液晶显示控制模块-LCD Control