资源列表
store
- 储物柜工业控制，包含电子锁控制，身份证ID读取-Lockers industrial controls, including electronic lock control, ID card reading
MT6795_MT6331
- MT6795+MT6331+MT6332+MT6330官方硬件参考设计-MT6795+MT6331+MT6332+MT6330 official Hardware Reference Designs
STM32F103ZET6_PCB
- STM32最小系统板的原理图设计和PCB图-STM32 minimum system schematic design and PCB board
FPGA
- FPGA和STM32F103的多轴控制硬件设计，包含原理图，PCB-FPGA and STM32F103 multi-axis control hardware design, including schematics, PCB
FXQ
- STM32F103设计的四旋翼飞行器遥控器硬件设计，包含原理图PCB-STM32F103 design of the four rotor aircraft remote control hardware design, including schematic PCB
TC6014
- STM32F103ZET6和专业的电机控制芯片TC6014设计的四轴电机控制器，包含原理图PCB-STM32F103ZET6 and professional motor control chip TC6014 designed four-axis motor controller, including the schematic PCB
fan_network664
- 96F664 fan controller at home net system-96F664 fan controller at home net system
m16-19264oscilloscope
- M16-19264示波器 位 定义 默认 ＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝＝ 0 运行状态 运行 1 触发模式 上升沿 2 画点模式 连线 3 DivY 4 Output_Freq 5 DivX 6 触发电平 7 频率 -M16-19264 oscilloscope define default bit Operation Status 0 1
power-circuit
- 在电源输入的前端利用旁路去耦电容滤波器，在+12V输入时，首先通过一个电解电容C1和电容C2保证电压的输入稳定，之后选择利用稳压器NCP1117ST50T3G将输出电压降到+5V，如图3.5所示，其输出电流为1A。在稳压器之后继续采用一个电解电容C3来保证输入到芯片的供电电压稳定。-Power input at the front end of the use of bypass decoupling capacitor filter when+12V input through a first
communication-circuit
- 由于RS232的电平与Arduino Mega 2560的接口电平不能兼容，所以就需要进行电平的转换，即进行串口转换模块的设计，本文选择利用ATMEGA16U2-MU模块来做电平转换，将上位机的指令通过此模块发给下位机-Since the RS232 level is not compatible with the Arduino Mega 2560 interface level, so we need to level conversion, that is designed to seri
core-circuit
- ATmega2560通过USB接口与PC进行传输，供电电压为5V，内部晶振为16MHz。该芯片共有有54个I/O引脚，特别适用于需要大量I/O口电路，其中的16个可以提供脉宽调制（PWM）模拟输出，还有另外16个模拟输入引脚。在通信方面，有4个硬件串口，另外也可以支持SPI通信和I2C/TWI设备。设计核心电路中加入复位按键，通过USB串口进行通信。-ATmega2560 through the USB interface with the PC for transmission, power
WTV40-yuyin-driver
- WTV40语音芯片驱动源代码，可独立调取128段音频文件-WTV40 voice control chip driver code, can be independently obtain 128 recordings