资源列表
CC26xx
- cc2460 蓝牙芯片 血氧测试代码,包含红外温度 测试代码(Cc2460 Bluetooth chip blood oxygen test code)
Altium-Designer-10-
- 这是一部关于描述altium designer10的书籍，通过此书籍的阅读，更好的设计电路图，为制作电路板，打下牢固基础。 -This is a book on the descr iption of altium designer10, through this book reading, better design circuit diagram, for the production of circuit boards, lay a solid foundation.
ST-Link V2
- STM32的JTAG / SWD接口是通过20PIN连接线连接目标板，所以ST-LINK/V2连接至STM32目标板时需要注意连接方向(The JTAG / SWD interface of STM32 connects the target board through the 20PIN connection line, so the connection direction needs to be noticed when ST-LINK/V2 is connected to the STM
2.13inch_e-Paper_HAT-code
- 用于驱动2.13英寸的墨水屏，电纸屏。包含arduino、STM32平台的源码。(Used to drive an ink screen of 2.13 inches, an electric paper screen. Contains Arduino, STM32 platform source code.)
CC1101-LAYOUT
- 这是参考官方设计手册做的一个CC1101模块，实测有效直线通信距离200米，绘制环境AD16(附51，MSP430程序设计参考资料以及TI PCB参考设计)-This is the official reference manual designed to do a CC1101 module, found effective communication distance of 200 meters straight draw Environment AD16 (Annex 51, MSP430
SchaPCB
- 基于arduino pro mini和mpu6050的迷你四轴原理图和PCB，本设计采用模块化，省去了难度较高的芯片焊接。-Based on arduino pro mini and mpu6050 small four-axis schematic and PCB, the design of modular, eliminating the need for more difficult chip welding.
Norflash_readid
- 通过镁光官网下载Norflash模型，然后编写v文件进行读取id测试，最后下载到FPGA板子，可以验证FPGA外接的Norflash是否工作
elec_sensor_mainborad
- 硬件电路PCB设计。飞思卡尔（恩智浦）智能车竞赛主板+电磁传感器（拼板）电路设计。主板K60。主板上置放有蓝牙、oled、电源、电机驱动模块等。开发环境是DXP-PCB hardware design。
SHUMAGUAN
- 在4位数码管上显示1234四个数字，可对静态和动态显示进行控制-In 4 digital tube display four 1234 numbers, can be static and dynamic display control
led
- 实现LED小灯呈现流水状闪烁，可自由改变闪烁频率-LED lights show water like flash, can freely change the flashing frequency
MB90F549G
- 富士通单片机 适用于MB9054系列硬件编程 网上资料很好 适合项目开发编程(Fujitsu microcontroller is suitable for MB9054 series of hardware programming online data well suited for project development programming)
nrf24l01多发一收
- 实现两个Nrf24l01发送，一个接收,然后将采集到的温度·数据发送到Mcu,mcu在oled屏幕上显示(Implementing two Nrf24l01 sending, one receiving, and then sending the collected temperature and data to Mcu, and MCU on the OLED screen)