搜索资源列表
DS18B20应用子程序
- 89C52单片机12M晶振下DS18B20温度传感器测量温度应用子程序源码-89C52 microcontroller 12M under DS18B20 crystal temperature sensor temperature measurement applications subroutine FOSS
DHT11_python
- python编程,使用Arduino和DHT11温度湿度传感器进行温度测量(Python programming, using Arduino and DHT11 temperature and humidity sensors for temperature measurement)
温度远程测量主机
- 用485总线进行传输数据,ds18b20测量温度,通过485总线传到主机(Using 485 bus to transmit data and measure temperature)
3
- 温度测量的卡尔曼滤波(Calman filter for temperature measurement)
Temperature_test
- 基于51单片机的实时温度测量程序及仿真。编程软件是keil,仿真软件是Proteus(Real time temperature measurement program and simulation based on 51 single chip microcomputer)
实验30 DS18B20 1602温度显示
- DS18B20温度传感器测量环境温度,并通过LCD1602显示出来(DS18B20 temperature sensor survey ambient temperature, and displayed by LCD1602)
18b20
- 此程序的测试平台是51单片机,利用DS18B20进行温度测量,达到上限时可以进行报警(The test platform of this program is 51 single chip microcomputer. The temperature is measured by DS18B20. It can alarm when the upper limit is reached.)
total
- 综合应用程序,包括VGA显示,温度测量等,便于初学者掌握使用verilog HDL语言的进行综合设计和使用(Comprehensive application program, including VGA display, temperature measurement and so on, is easy for beginners to master and use Verilog HDL language for comprehensive design and use.)
作业1.1
- 使用随机函数模拟生成温度,测量温度并统计温度直方图(Randomly generate temperature, measure and record the histogram)
PT100
- 51单片机实现PT100温度测量程序,采用恒流源测量原理(Realization of PT100 temperature measurement program by 51 single chip microcomputer)
4-20ma RTD
- 可测量和处理来自 2 线、3 线和 4 线电阻式温度检测器的温度信号输入,并输出与来自 RTD 输入的所处理的温度相对应的 4 至 20 mA 电流回路信号,并进行系统级的校准以提高 ADC 和 DAC 精度。(It can measure and process the temperature signal input from the 2-wire, 3-wire and 4-wire resistive temperature detector, and output the 4-20 m
无创血压、血氧、温度、皮电测量单片机程序
- 无创血压、血氧、温度、皮电测量单片机程序 使用uVision编程的下位机程序 能够在显示屏上显示(Non-invasive blood pressure, blood oxygen, temperature, skin electrical measurement of single-chip microcomputer program using uVision program can be displayed on the display screen)
基于单片机的温度计
- 基于单片机的温度计设计,能实现温度测量。
DHT11温湿度显示程序
- 利用stm32以及dht11芯片,实现温度与湿度的测量与在OLED上显示、阀值警报以及触摸按键的控制。(Using STM32 and DHT11 chips, temperature and humidity measurement and OLED display, threshold alarm and touch button control are realized.)
STM32驱动max6675测温的测试例程
- 通过使用stm32f103系统的单片机,通过程序,驱动max6675测量温度(By using the MCU of STM32F103 system, the MAX6675 can be driven to measure the temperature through the program)
基于单片机控制的多功能电子时钟设计
- 本设计使用 11.0592MHZ 晶振与单片机 AT89C52 相连接,以 AT89C52 芯片为核心,采用 LCD1602 的并行操作方式显示。通过使用该单片机,实现把时间和温度显示LCD1602 液晶上,并且实时更新。 STC89C52 单片机是由深圳宏晶科技公司推出的,功耗小,电压可选用 4~6V 电压供电。通过单片机实验箱上的按键可随时调节时钟的年、月、日、星期、时、分、秒; 并且可以进行闹钟设置,切换界面等操作,另外还附加温度测量与报警模功能按键设计 4 个有效按键,分别有时钟调整键、
MDT
- LTC2984 STM32测试工程,高精度多路数字温度测量(LTC2984 STM32 Test Demo)
基于ATmaga8 的Pt100温度计设计
- 设计Pt100铂电阻测量温度的电路,温度测量范围是0-100摄氏度,要求LCD显示。画出电路图,标注元器件参数,简单说明测量原理和调节方式。根据要求,本设计的测温模拟电路使用热电阻Pt100温度传感器利用其感温效应,热电阻随环境温度的变化而变化,在电路图中将电阻值的变化转换成电压的变化,再将电压值作为输入信号输入至AD转换器中进行模拟信号到数字信号的转换,其输出端接单片机,向单片机内依据公式写入源程序,将被测温度在显示器上显示出来: 测量温度范围0℃~100℃; 分辨率为0.1℃; LCD
测温
- STM32 UCOS 实现温度测量 使用keil5
51单片机测量温度
- 通过温度传感器来测量温度,并传给51单片机,进来处理温度